Milnor K36 0005R, K28 0010 manual Tension Settings-Unbanded Belts

Page 7

MSSMA405AE/8737BV

V-BELT TENSION ADJUSTMENTS

FOR 48", 52", 60" AND 72" WASHER-EXTRACTORS

This instruction is to be used for adjusting the belt tension on the following machine models:

 

 

 

 

 

 

 

 

48032BHE

48032BTG

48032BTH

48036QHE

48036QTG

48036QTH

 

 

52038WE1

52038WTF

52038WTB

52038WTG

52038WTH

 

 

 

60036WE2

60036WE3

60036SG2

60036SG3

60044WE2

60044WE3

60044SG2

60044SG3

72044SG2

72044SG3

72044WE2

72044WE3

72044WTB

72044WTG

72044WTH

 

 

 

 

 

 

 

 

 

 

 

A belt tension testing device (Milnor®

part number 30T001) and a straight edge are required when tensioning

unbanded belts.

Tension Settings—Unbanded Belts

Set the o-rings on the tension testing device (see FIGURE 1) as follows:

1.Move the upper o-ring to the topmost position, resting against the bottom edge of the cap.

2.Find the proper belt deflection setting (by machine model and belt function) in the appropriate table below.

3.Move the lower o-ring on the tension tester to this deflection setting on the in- ches scale.

NOTE 1: The tension testing device is marked on one side in inches and pounds and on the other side in centimeters and kilograms. All values in the tables are in inches (in.) and pounds (lbs.).

NOTE 2: The instruction sheet provided with the tension testing device should not be used. Use only the instructions provided herein.

NOTE 3: The reference (ref.) code shown in the tables are for factory use only.

Upper o-ring

Deflection force scale (read down)

Deflection distance scale (read up)

Lower o-ring

FIGURE 1 (MSSMA405AE)

Tension Settings

5

Image 7
Contents Kit Instruction K28 K36 K36 0005R Trademarks of Pellerin Milnor Corporation References to Yellow Troubleshooting PagesPlease Read About the Manual Identifying Information on the CoverPage Belt Tension Measurements Tension Settings30016BWE 36026QWEMSSM0301AE/9126BV Belt Tension AdjustmentsTaking Measurements with the Tension Tester Belt Tension Measurements42031WE2/WE3 and 42044WE2/WE3 Belt Tension Measurements 42031SG2/SG3 and 42044SG2/SG3 Belt Tension MeasurementsTension Settings Tension Settings-Unbanded BeltsMeasuring Belt Tension Unbanded Belts60036 + 60044WE2 + WE3 Tensioning Banded Belts 48032BHE, BTG, BTH 48036QHE, QTG, QT52038WE1, WTF, WTB, WTG, WTH 60036 + 60044WE2 + WE3 48032BHE, BTG, BTH 48036QHE, QTG, QTPage MSSM0303AE/8451BV Front Bearing Assembly Rear Bearing AssemblyConnection From Hydraulic Pump to Assist in Bearing Removal Removing the Bearing Front or RearMSSM0303AE Rods in Position Fixture in PositionPrecautions for Bearing Replacement Installing Seals Installing Seal Sleeve MSSM0303AE Bridge for 42 machine shown Measuring Unmounted Clearance Setting Bearing Front or RearTable of Bearing Clearances Tightening the Bearing Measuring the Mounted Internal Tightening Bearings Front and/or RearClearance of the Bearing