Various Functions, No Trouble Conditions

Water Inlet

VARIOUS FUNCTIONS

OTHERS

1.Delete the end buzzer: Press POWER ON/OFF button to switch on the power, and press START/PAUSE button for 4 seconds till a sound from buzzer. To restore it, repeat above or pull out the plug.

2.How to drain remaining water

When select this function, in 9 minutes after the working finished, the drainage valve will open to drain out the remained water inside. This will avoid water freezing inside in winter when temperature below 0℃.

●Method of Use

Press POWER ON/OFF button to switch on the power, and press PROCESS button for 4 seconds till a sound from buzzer. To restore it, repeat above or pull out the plug.

NO TROUBLE CONDITIONS

1.During Washing or Rinsing, still there is Water inletting. This is possibly automatic water adding due to water level decrease.

2.Spin tub turns or stops timely at the beginning of spinning. This is intermittent spinning for better spin effect.

3.No drainage during overflow rinse. This is caused by lower water level set or lower water pressure.

4.Water inletting and rinsing sometimes during spinning. This is automatic lean-correction due to clothe is not equally inside.

5.There is sound like water flow after spinning. This is the sound of balance liquid in Balance ring. It is for reducing vibration of spinning.

6.Control panel keeps warm after Power Off, this is caused by Remember circuitry working.

7.Power off during working and the washer could not continue working. Should set the program again.

CARE AND MAINTENANCE

TROUBLE SHOOTING GUIDE

When the following problems occur, the microcomputer will detect the abnormal condition and an electronic buzzer sounds for approximately 10 seconds and digital display indicates flash as shown below.

Kind of Trouble	Trouble	Where to Check
	Indication
		● Check the POWER ON/OFF button.
		● Check the START/PAUSE button.
The washer		● Check whether under PRESET condition.
does not work		● Check the power cord whether is securely plugged in.
at all		● Check whether power failure occurs.
		● Check whether the fuse or circuit breaker has been
		activated.
Water does		● Turn on the water supply faucet.
Water does		● Check whether water supply has been cut off.
not flow into		● Check whether water supply has been cut off.
not flow into		● Check whether the metal filter in water inlet is clogged.
tub or water		● Check whether the metal filter in water inlet is clogged.
tub or water		● Check whether washer has been freezing.
flow is slim		● Check whether water pressure is too low.

Water does		● Check whether the Drain Hose has been put down.
Water does		● Check whether the drain hose rises too high.
not drain out		● Check whether the drain hose rises too high.
not drain out		● Check whether the drain hose is clogged.
		● Check whether the drain hose is clogged.

		● Check whether the laundry is clumped on one side of tub.
The washer		● Check whether the washer is on the level surface.
The washer
does not spin		● Close the washer lid.
		● Close the washer lid.

Clean washing machine

Use soft clothing to wipe off the water or dirt on the surface of the washer.

● Do not spray water directly to the washer body.

● Detergent, propellant and other chemicals are not allowed to use to avoid the damages on the surface.

Clean “ magic ” hose joint filter

(Suggest clean it every 6 months) 1. Pull the water inlet hose out.

2. Turn off the revolver according to below figure.

3. Load off the “ Magic ” Hose Joint

filter and clean the crud with a toothbrush.

4.Install the clean “ Magic ” Hose Joint filter to revolver and water inlet hose.

Filter

Clean the water inlet valve

(Suggest clean it every 6 months)

After long time use, The water inlet mesh bag may be blocked with crud,

please load off the water inlet hose, take out the water inlet mesh bag

from the water inlet valve, clean the mesh bag, then assemble the mesh bag in the valve and load the water inlet hose.

Clean lint filter

(Suggest clean it every week) 1. Take out the lint filter

2. Pull out the scraps and wash

the lint filter in the water.

3. Install the Filter. aim the frame claw to the groove below.

( Lint Filer is easily destroyed parts).

	Does not wash	● Check whether the washer is under Child Lock.
	Does not wash	● Close the washer lid.
		● Close the washer lid.

Other troubles		Press the POWER ON/OFF button, call the local
Other troubles		service-person or dealer.
		service-person or dealer.

NOTE: The Trouble indicators can be released by pressing the START/PAUSE button once if you want to release the emergency stop. Then press the START/PAUSE button again to restart the operation.