Sanyo ASW-A85HT, Microcomputer Control Fully Automatic Washing Machine Installation Instructions

Page 4
Drain Hose Hose Clip
Drain hole cover
Drai n Valve
Hose Clip
when changing the Drain Hose direction.
Drain hole
Drain Hose
Drain hole
Frame
Hose Band
Drain Valve
Drain Hose

INSTALLATION INSTRUCTIONS

How to Attach the “ Magic ” Hose Joint

1.Loosen the four screws and slide the top of the "Magic"Hose Joint(section A in the figure)onto the faucet. Then, securely tighten the four screws provided with the “Magic" Hose Joint by using a screwdriver to secure the top of the joint to the faucet.

2.Remove the CAUTION label from the "Magic" Hose Joint.

3.Turn the male coupler on the joint (section B in the figure) clockwise to attach it securely

to the top of the joint (section A in the figure).

INSTALLATION INSTRUCTIONS

Installing The Drain Hose

Set the clip part of Hose Band sideways to prevent touching the frame which may cause a vibration noise.

Inside Hose

Drain Outlet

Drain Hose

● The appliance is to be connected to the

 

 

water mains using new Water Supply

Screw

After tightened

Hose and “Magic" Hose Joint and old

A

 

 

Hose Band

Hose Protector

Drain Outlet

(A Sectional Plan)

hose-sets should not be reused.

About 4mm

(About 2mm or less)

CAUTION

B

CAUTION:label

If outer diameter of faucet is larger than

calibre of the Joint Ring, loosen the four

screws and remove the Joint Ring from Joint Ring the "Magic" Hose Joint.

Installing Water Supply Hose to the Washer

1.Turn the nut clockwise while holding the hose.

 

● Turn the nut counterclockwise after turning the

Nut

faucet off when you want to detach the Water

Hose

 

Supply Hose.

 

Connecting the Water Supply Hose to the “ Magic ” Hose Joint

1.While pushing the sleeve on the female coupler

C

Lock Lever

(section D in the figure) of the joint down with

Sleeve

your fingers, connect the female coupler to the

 

male coupler (section C in the figure).

D

2.Release the sleeve, then push the Water Supply

 

Hose up into the “ Magic ” Hose Joint until it

 

clicks into place.

 

3.Pull the Water Supply Hose down to make sure

 

that it is securely attached.

 

How to Detach the Water Supply Hose

Please read the following procedure in order to avoid spilling water when detaching the Water Supply Hose.

1.Turn the faucet off.

 

2.Press the POWER ON/OFF button to turn the power on ,the

C

Changing the Drain Hose Direction

You can change the direction from right side to left side.

NOTE:

Put gloves on to prevent injury of your hands

1.Unplug the Power Cord of the washer. 2.Detach the Back Cover by loosening screws at the back side of the washer.

Detach outer Drain Hose and gently lay down the front side of washer on a soft mat or cushion.

Be careful not to open the Washer Lid and dent the frame.

3.Detach the Cap from the left side of frame. 4.Loosen the Hose Band and pull the inner Drain Hose out of the Drain Valve. Pull the Hose Band out of the inner Drain Hose.

5.Remove right and left Tabs of Drain Outlet one side by another side pushing the Tabs both in side and outside and pull the Drain Hose out toward outside of frame.

6.Let the inner Drain Hose through outside of left hole and set the protrusive guard of inner Drain Hose to the square cutting part of frame, then attach the Drain Out let of the hose until fitting the Tabs certainly to the frame.

7.Connect the inner Drain Hose to the Drain Valve in place and fix the Hose Band as shown below.

If you do not attach correct position marked with ,it can damage the inner Drain Hose and cause a water leaking through the torn position.

8.Attach the Cap to the right hole.

9.Reattach Back Cover and gently set the washer upright.

Extension of the Drain Hose

When extending the external Drain Hose, please follow the below figure for the length and height.

NORMAL button and the START/PAUSE button.

 

 

3.Press the POWER ON/OFF button to turn the power off

Lock

 

15 seconds later.

Lever

Sleeve

4.While pushing the lock lever and the sleeve on the female

 

 

(section D in the figure)of the joint down with your fingers,

D

 

detach the female coupler from the male coupler

 

 

 

(section C in the figure).

 

 

Extension Hose

 

Height

Length

 

 

 

 

 

No straight

Max.15cm

Max.1m

 

 

 

 

 

Straight

 

 

 

Max.3m

 

 

 

 

 

 

 

 

Max.1m

Max.15cm

5

6

Image 4
Contents Specifications ASW-A85HTContents Important SafeguardsAccessories Installation Instructions Name of PartsInstallation Instructions Installation InstructionsDetergent Indicators Names and Functions of Control PanelSoak → Wash → Rinse → Spin → Preset Water PowerNormal Usage Suitable ClothesVarious Functions Various FunctionsRinse Type and Rinse Times Trouble Shooting Guide Where to CheckClean the water inlet valve Various Functions