Smeg WDI12C instruction manual Cleaning the Detergent Tray, Cleaning the Water Inlet Filter

Page 27

GB

3.Pull out the drain hose “A”.

Attention: if the hose is hot it means the water is hot or boiling. Place a tray on the f loor and remov e the plug “B” to drain the water. Depending on the quantity of water, it may be necessary to empty the tray sev eral times.

When no more water comes out, push the hose back in and screw back the plug “B”.

4.Unscrew the cov er of the pump “D” by turning it anti-clockwise. Clean the pump body and remov e any f oreign bodies.

Check the inside “E” and make sure the impeller turns f reely. If there are any f oreign bodies, remov e them.

5.Screw the pump cov er back on.

Fix the drain hose by snapping the plug into place «C». Depending on the model, put back the cov er as f ollows:

MODEL A – Insert the lower part of the cov er f irst. Then secure it by turning the plastic buttons a quarter turn clockwise.

The slots in the buttons must be horizontal.

MODEL B – Insert the lower part of the cov er first and then push it towards the base plate until it clicks into place.

7.5CLEANING THE DETERGENT TRAY

Keep the detergent tray free from scale.

To simplify this operation, completely remov e the detergent tray (pull it out as f ar as it will go, lift it slightly and then pull fairly v igorously ).

Remov e the traps «B» (there are two traps if the machine is not f itted with a cov er for the bleach compartment) and clean with hot water.

Put back the traps and remove any residues of detergent bef ore putting the tray back.

7.6 CLEANING THE WATER INLET FILTER

The machine is fitted with a filter f or protecting the water inlet valv es.

The f ilter is fitted the gas thread of the inlet hose connected to the tap

Clean the f ilter if no water or insufficient quantities of water enter the washing machine. To do this, proceed as follows:

•Remove the plug from the socket to disconnect the machine from the electrical power supply.

•Turn off the water tap.

•Unscrew the inlet hose from the tap.

•Remov e the f ilter from the inlet hose gas thread.

•Clean the f ilter with water and a brush.

•When screwing the inlet hose back on to the tap, make sure the f ilter is correctly positioned.

27

Page 26 Page 28
Image 27
Page 26 Page 28
Contents Integrated Washer Dryer Contents NEW Washing System Sibility for uses other than those described above Safety WarningsAnce Prolonged inactiv ityUnpacking Installation InstructionsWater Supply Connection Additional Important Installation InstructionsElectrical Connection Drain ConnectionFitting the Furniture Doors Fitting the hinge components to the furniture door Use of the furniture door fixing templateFitting the plinth Recessing the applianceDescription of Controls Control PanelOpen door button ON-OFF and programme selection knob Select the drying programme Time remainingEnd of cycle END Error codesLED Spin speedTion for heating increases Detergent Tray Options enabled LEDsWashing Instructions Preparing the WashingOpening the Door Adding Detergent and Additiv ES Loading the WashingDosing Powder Detergents Dosing Liquid DetergentsSCALE-REMOV ERS Options Modifying Starting Param EtersEND of Programme Turn the programmes knob to OFF to switch off the machineStarting the Washing Programme Interrupting or Changing the Washing ProgrammeDrying Instructions END of Programme BeeperGeneral WASH-ONLY Programmes WASH+DRY Programmes5kg Example DRY-ONLY ProgrammeInterrupting or Changing the Drying Programme END of Drying ProgrammeProgramme Finished Buzzer Cleaning the Door Gasket Cleaning and MaintenanceExternal Cleaning Cleaning the DrumCleaning the Water Inlet Filter Cleaning the Detergent TrayTroubleshooting Error Signals Control Panel Symbols ProgramsSection Hemp fabrics Programme Guide KEY to Button
Top Page Image Contents