IFB Appliances AW60-806 operation manual Following cases are not faults, Solution, Clasper, Slot

Page 9

METHOD OF MAINTENANCE

TROUBLE SHOOTING

The following cases are not faults

1.There is water injection in time of washing or rinse, which is due to that the washer senses the

inadequacy of water and exchanges water level automatically.

2.There is the phenomenon of intermittent spinning in the beginning of spinning, which is performed

to achieve better spinning effects.

3.In the course of spin, the program return to the wash program. Because that is designed to rectify the unbalanced distribution of load in the spin tub.

Exceptional

phenomenon

No indication in controller

The inlet hose

.leakage

Cause

The power plug is not plugged tight.

The power switch is not switched

on.

Not press "START/PAUSE" button.

Power cut.

Do not rightly connect the tap with

the universal connector.

Do not screw tight the nut of the

water inlet hose.

Solution

Re-plug the power plug.

Check the power socket, or change other

socket.

Press "START/PAUSE" button.

Wait for switching on electricity.

Re-install rightly the universal connector.

Screw tight the nut.

Method Of Maintenance

After the whole washing program

The washing machine will send off the "DOU- DOU"sound after any program operation to remind you of taking out the load or going on with other operations.

After finishing washing, please shut off the tap, pull out the plug in case of water leakage or fire

Cleaning the water inlet

After long time use, the water inlet mesh bag may be blocked with smudginess, and should be cleaned according to the following steps:

1.Switch on the power, followed by shutting off the tap .

2.Let the washer works for 5 seconds so that water flows into the tub through the water inlet hose. then turn off the power.

3.Unload the water inlet hose and clean the mesh bag, then restore the water inlet assembly.

Maintenance of shell

Use soft cloth to wipe off the water and dirt on the surface each time after use of the washing machine. Detergent, propellant and other chemicals are not allowed to use, for they can cause damage to the surface.

Cleaning of the lint filter

A f t e r u s i n g t h e

 

washing machine for a

 

period,

please clean

 

according the

following

 

steps:

 

 

 

1. Take out the lint filter.

 

2. Turn the mesh bag

Clasper

outside

and

wash it

clean in the water.

3. Restore it and refix it.

Slot

Does not drain

Dose not inject water

Spinning stops and water injecting begains in the course of spin

Does not spin

Intermittent spinning

Before using the machine water exists in the drain hose.

Notices:

The drain hose is wrung or jammed.

Stop water.

Do not open the tap.

Whether the wire netting in the water

inlet was stopped up by the sundries.

Cause by that the washing

After end to drain, do not close the lid.

Open the lid in course of spinning.

In order to attain the better

spinning effect.

Remainning water due to testing

or experiment in the factory.

Loosen the drain hose for smooth flow of water

Wait for coming water.

Open the tap.

Clean the netting according to the method of

"Cleaning of the water inlet".

This is automatic rectification for spinning in the washing program. That the washing are too much or too little, or that the washing machine is not placed plane will cause the unbalance in time of spinning. If there is still abnormal circumstances after checking the above-mentioned points, please pull out the power plug and contact with local service as soon as possible.

Close the upper lid.

Belong to the normal phenomenon generally.

Belong to the normal phenomenon generally.

The washing machine does not work normally because the voltage is low or too high. Please pull

out the plug and wait till the voltage becomes normal.

If there is still abnormal circumstances after checking the above-mentioned points, please pull out

the plug. Do not repair it by yourself at home, which is very dangerous.

15

16

Image 9
Contents Fully Automatic Washing Machine Features Features and AccessoriesSimple Installation Names of Respective Parts and Simple InstallationSimple installation Names of respective partsPower source and grounding Simple Installation and Simple OperationInstallation of the drain hose Simple operationAW60-806 Water levelLight/Flash Bulky Wool ProgramDrain Water injectionTotal Confirmation of the preset and inspection Preset programCancel the preset, or alter the preset time Operation MethodWeight standard of the clothes Use the cleaning solution for twicePre-wash of dirty clothes Load size and the detergentSolution Following cases are not faultsClasper SlotSafe use of power Function of fault alarmFunction of automatic power-off Function of adjusting for unbalancePage Page Page Rated input power SpecificationsRated voltage Rated Frequency 50Hz