Whirlpool 3360620 installation instructions Now start, With washer in laundry area

Page 4

Now start...

With washer in laundry area.

WARNING

Excessive Weight Hazard

Use two or more people to move and install washer.

Failure to do so can result in back or other injury.

Inlets are plastic. Do Not strip or crossthread.

3.Attach hose to bottom inlet valve opening first. Then second hose to top inlet. Tighten couplings by hand; then use pliers to make an additional two-thirds turn.

Slide washer onto cardboard or hardboard before moving across floor.

16"

6.Measure and mark a point approximately 16 inches from the plug end of the shipping strap. Cut this shipping strap at this point.

Check that hose is not twisted or kinked and is securely in place.

Put “hook” end of drain hose into standpipe. Tightly wrap the shipping strap around the standpipe. Push plug into the nearest hole in the shipping strap.

shipping tape

Pull the strap completely

out of the washer.

1.Remove tape that covers shipping strap. Pull to completely remove the shipping strap with

2 cotterpins from the inside of the washer.

Pull firmly to remove the

end of shipping strap from the back of the washer. The shipping strap plug must be completely removed from the washer for the self-leveling legs to be released.

Save the shipping strap for use in Step 6.

Power supply cord is factory installed. Peel the tape down and off each side of the cabinet.

Use the new hoses and washers that came with your Whirlpool washer.

coupling washer

2.Insert a flat washer into each end of the inlet hoses. Check that washers are firmly seated in couplings.

PAGE 4

4.Move washer close to final position. Put “hook” end of drain hose into standpipe. Estimate length of drain hose needed when washer is in final position. Hose must be cut exactly to length so “hook” end is held tightly over edge of standpipe. If drain hose is too long, cut straight end of hose. (Do Not cut “hook” shaped end of drain hose.)

DO NOT FORCE EXCESS LENGTH OF

DRAIN HOSE DOWN THE STANDPIPE.

THIS COULD CAUSE SIPHONING. See

Step 6.

5.Place hose clamp over washer drain connector. Push drain hose onto washer connector. use pliers to open clamp and slide clamp over drain hose. Check for good fit.

7.Before attaching water inlet hoses, run water through both faucets into a bucket. This will get rid of particles in water lines

that might clog hoses.

Mark which is the hot water faucet.

8.Attach bottom hose (inlet marked “H”) to hot water faucet. Attach top hose (inlet marked “C”) to cold water faucet. Tighten coupling to faucet by hand; then use pliers to make final two-thirds turn.

9.Stack two corner posts on top of each other. Tilt washer backwards and insert corner posts 3 inches in from one side of washer as shown. Repeat with other corner posts on other side of washer.

1/2"

base

nut

10.Use legs and nuts from parts package. Screw nut down to within 1/2 inch of base.

11.

Insert legs into correct holes at each front corner of washer until nuts touch washer. Do Not tighten nuts until Step 15.

Image 4
Contents Installation Instructions Your safety and the safety Others is very important Before you startTools needed for installation Parts supplied for installationElectrical requirements Recommended ground methodNow start With washer in laundry areaBolt Owner options coin- operated models Typical full load sizesCheck list for washer operation Operating Tips

3360620 specifications

The Whirlpool 3360620 is an essential component for those looking to enhance the functionality of their kitchen appliances, specifically designed for certain models of Whirlpool refrigerators. This replacement part primarily serves as a door shelf bin, catering to the storage needs of users by providing additional space and organization for condiments, beverages, and small food items.

One of the standout features of the Whirlpool 3360620 is its robust construction. Made from high-quality plastic, it is designed to withstand the rigors of daily use while maintaining its structural integrity over time. This durability ensures that it won’t easily warp or crack, providing long-lasting service in the often humid environment of a refrigerator.

The design of the 3360620 is also noteworthy. It features a clear, see-through appearance, allowing users to quickly identify contents without needing to remove the bin. This transparency enhances organization and efficiency, making it easier to find what you need at a glance. Measuring approximately 13 x 6 inches, it fits perfectly within the door of compatible Whirlpool models, maximizing space and usability.

Another significant characteristic of this replacement part is its ease of installation. Designed as a direct fit for specific Whirlpool refrigerator models, it can be installed without the need for special tools, making it accessible for most users to replace on their own. This feature is particularly important for those who prefer DIY repairs and maintenance.

In terms of compatibility, the Whirlpool 3360620 fits several refrigerator models, and it’s always recommended to check the appliance’s model number to ensure a proper fit. This versatility makes it a popular choice among Whirlpool users who seek to prolong the lifespan of their appliances while maintaining organized storage solutions.

Overall, the Whirlpool 3360620 door shelf bin combines durability, efficient design, and easy installation, making it a valuable addition to any Whirlpool refrigerator. It helps users keep their kitchen organized and maximizes the available space, reflecting Whirlpool’s commitment to quality and customer satisfaction.