Bolt

12.Tilt washer backward and remove corner posts. Gently lower washer to floor.

Move washer to its permanent location. Remove cardboard or hardboard from under washer.

18.CHECK ELECTRICAL REQUIREMENTS. BE SURE YOU HAVE CORRECT ELECTRICAL SUPPLY AND RECOMMENDED GROUNDING METHOD.

Rotate counter- clockwise only.

timer “off” position

timer-front view

13.Tilt washer forward raising back legs 1 inch off of floor. To adjust

	19.Check that all parts are now	• Coin-operated timers can be
		started by turning the clutch
		assembly counterclockwise until the
	installed. See parts list, Page 3. If there	assembly counterclockwise until the
	installed. See parts list, Page 3. If there	washer starts to fill with water.
	is an extra part, go back through	washer starts to fill with water.
	is an extra part, go back through
	steps to see which step was skipped.

rear self-leveling legs, gently lower washer to floor. Check levelness of the washer by placing a carpenter’s level on top of the washer, first side to side; then front to back.

14.If washer is not level, screw the front legs up or down to adjust. Make final check with level.

When washer is level, use wrench to turn nuts on front legs up tightly against washer base. If nuts are not tight against washer base, the washer may vibrate.

15.On coin-operated washers, remove the service door of the meter case. Lift the service door up at the back and remove. Carefully insert coin slide with the coin slide extension attached into front opening and secure with the 3/16" mounting bolt from inside the meter case. The coin slide may need to be partially pushed in to insert mechanism in the front opening. Replace meter case top and service door. Insert coin vault with lock and key.

20.Turn on water faucets and check for leaks. Tighten couplings if there is leaking. Do Not overtighten; this could cause damage to faucets.

21.Check that you have all of your tools. Check that the shipping strap with 2 cotterpins and plug was removed from the back of the washer and used to secure the drain hose.

If entire strap is not removed, washer may vibrate and be noisy.

22.Remove power supply cord from basket and plug into grounded outlet.

23.Check the wash cycle time. Both coin-operated and non-coin- operated washers have timers with a 9-minute wash in the Normal cycle. Remove the meter case top of coin- operated washers to manually start the timer. Remove the rear of the console to manually start the timer. Remove the rear of the console to manually operate the timer of non- coin-operated washers. Start the washer and allow it to complete the Normal cycle.

		Rotation	Rinse
cycle		Drain	Rinse
cycle		Drain
information		Spin	pin
		Spin	S
	Off		Drain
	Off		Wash
			Wash

lever

pull to start push to stop

timer-rear view

•Non-coin-operated timer cycle information is ink stamped on the rear of the timer. Push in on the lever attached to the timer shaft. Reset lever to the Normal cycle position, then pull out on lever to start washer.

24.If the washer fails to start or does not give the proper washer cycle time, the clutch assembly of the coin-operated timer can be adjusted. Remove the timer from the meter case. Adjust the clutch assembly screw clockwise, if the washer does not start after the coin slide mechanism has been fully actuated in or out. Adjust the clutch assembly screw counterclockwise if the washer segment of the Normal cycle was less than 9 minutes.

timer clutch adjustment screw

PAGE 5

3360620 specifications

The Whirlpool 3360620 is an essential component for those looking to enhance the functionality of their kitchen appliances, specifically designed for certain models of Whirlpool refrigerators. This replacement part primarily serves as a door shelf bin, catering to the storage needs of users by providing additional space and organization for condiments, beverages, and small food items.

One of the standout features of the Whirlpool 3360620 is its robust construction. Made from high-quality plastic, it is designed to withstand the rigors of daily use while maintaining its structural integrity over time. This durability ensures that it won’t easily warp or crack, providing long-lasting service in the often humid environment of a refrigerator.

The design of the 3360620 is also noteworthy. It features a clear, see-through appearance, allowing users to quickly identify contents without needing to remove the bin. This transparency enhances organization and efficiency, making it easier to find what you need at a glance. Measuring approximately 13 x 6 inches, it fits perfectly within the door of compatible Whirlpool models, maximizing space and usability.

Another significant characteristic of this replacement part is its ease of installation. Designed as a direct fit for specific Whirlpool refrigerator models, it can be installed without the need for special tools, making it accessible for most users to replace on their own. This feature is particularly important for those who prefer DIY repairs and maintenance.

In terms of compatibility, the Whirlpool 3360620 fits several refrigerator models, and it’s always recommended to check the appliance’s model number to ensure a proper fit. This versatility makes it a popular choice among Whirlpool users who seek to prolong the lifespan of their appliances while maintaining organized storage solutions.

Overall, the Whirlpool 3360620 door shelf bin combines durability, efficient design, and easy installation, making it a valuable addition to any Whirlpool refrigerator. It helps users keep their kitchen organized and maximizes the available space, reflecting Whirlpool’s commitment to quality and customer satisfaction.