JVC CA-MXJ10 Presetting Stations, Changing the FM Reception Mode, Three ways to select a station

Page 14

TUNING

UP

TUNING

DOWN

Three ways to select a station ——————————————

oPress the TUNING UP or TUNING DOWN button repeatedly to move from frequency to frequency until you find the one you want. (Manual Tuning).

OR

oPress and hold the TUNING UP or TUNING DOWN button for a few seconds, and the frequency starts changing on the display. When a station is tuned in, the frequency stops changing. (Auto Tuning).

OR

o Possible only after presetting stations.

P. DOWN

P. UP

Press once and release the P. DOWN 4 or ¢P. UP button to go to the next preset station.

You can also use the Remote Control to tune in preset channels:

1.Press the FM/AM button so that you can receive the most recent station tuned in.

2.Select the station by entering the preset number on the number keys of the Remote Control.

Example: For channel 5, press 5. For channel 15, press +10 then 5.

For channel 20, press +10, then 10. For channel 30, press +10 twice then 10.

After you have selected the preset number and the number is displayed, the broadcast frequency of the selected channel is displayed.

1

CDFM/AM

TAPE

AUX

or

FM/AM

 

2 TUNING UP

TUNING

DOWN

3

CLOCK

TIMER

 

1

2

3

 

SELECT +

4 5 6

SET

7 8 9

10 +10

Presetting Stations

You can preset up to 30 FM stations and up to 15 AM stations for the preset numbers.

Note: In some cases, test frequencies have been already memorized for the tuner since the factory examined the tuner preset function before shipment. This is not a malfunction. You can preset the stations you want into memory by following the presetting method.

1.Select a band by pressing the FM/AM button.

2.Press the TUNING UP or TUNING DOWN button to tune into a station.

3.Setting the preset number by pressing the number keys on the Remote Control:

For preset numbers 1 to 10:

Press and hold the number key for the preset number you want to set.

For preset numbers 11 to 20:

Press and hold the 1 to 10 buttons after pressing the +10 button.

For preset numbers 21 to 30:

Press and hold the 1 to 10 buttons after pressing the +10 button twice.

Release the button after the number starts to blink. This completes the preset setting.

4.Repeat steps 1 – 3 for each station you want to store in memory with a preset number.

CAUTION: If the Unit is unplugged or if a power failure occurs, the preset stations will be erased after a few days. If this happens, preset the stations again.

FM MODE

Changing the FM Reception Mode

When an FM stereo broadcast is hard to receive or noisy, press the FM MODE button on the Remote Control so that the “MONO” indicator lights up on the display. Reception improves, but there is no stereo effect.

To restore the stereo effect, press the FM MODE button on the Remote Control so that the “MONO” indicator goes off. In this stereo mode, the “ST” indicator lights up and you can hear stereo effects, when a program is broadcast in stereo.

11

Image 14
Contents CA-MXJ10 CA-MXJ10 Important for the U.KClass Laser Product Power cord FeaturesInstallation of the Unit How This Manual Is OrganizedTable of Contents Using the Remote Control AccessoriesHow to Put Batteries in the Remote Control Getting StartedUsing the Supplied Wire Antenna Connecting the FM AntennaConnecting the AM MW/LW Antenna Using the Standard Type Connector not suppliedVCR or other equipment Connecting the SpeakersConnecting Auxiliary Equipment Right SpeakerOn the Remote Control On the UnitDisplay Turning the Power On and OffCommon Operations Turning the System OnSound Modes Adjusting the VolumeReinforcing the Bass Sound Set the Volume control to Press the AUX button Listening to Auxiliary EquipmentSwitching between Frequency Bands Using the TunerTuning in a Station One Touch RadioThree ways to select a station Presetting StationsChanging the FM Reception Mode Repeat Using the CD PlayerDisc display RandomQuickest Way to Start a CD Is with the One Touch Operation For Normal Play Play mode indicator is not litInserting Discs Place a CD, with its label side up, onto the trayPlaying a Disc Basics of Using the CD Player Normal PlayLocating a Track with the Remote Control Directly Selecting a Disc, Track or Passage Within a TrackContinuous Play Programming the Playing Order of the TracksRandom Play Press the Random buttonLocking the Electronic Lock Repeating a Selection or the DiscsTray Lock Function Unlocking the Electronic LockRegular Play Using the Cassette DeckTape Direction Indicator on the Display One Touch PlayFast Left and Fast Right Reverse ModeMusic Scan Finding the Beginning of the Current SelectionDubbing REC START/STOP CD REC Start Things to Know Before You Start RecordingREC Pause Check the recording direction for the tape Standard RecordingRecording Any Sound Source to Tape Press the 2 or 3 buttonTape to Tape Recording Dubbing How to Use the Dubbing ButtonCD Direct Recording Press the Shift button Press the Clock button Using the TimerSetting the Clock Press the Select + or button to set the timeSet the time you want the Unit to be turned off Setting the TimerSet the time you want the Unit to come on Press the Select + or button to select the sourceTo Cancel the Sleep Timer Setting Setting the Sleep TimerTo Change the Sleep Timer Setting = 10 =20 = 30 =60 = 90 = 120 = CancelledCare And Maintenance Possible Cause TroubleshootingSymptom ActionSpecifications 0699KSMMDWHIT