Indesit WD 12 X manual Your safety and that

Page 17

Important for the safe use of your washer-dryer

Your safety and that of

your family Your washer-dryer has been built in compliance with the strictest international safety regulations.

To protect you and all your family.

Read these instructions and all the information in this manual carefully: they are an important source, not only of numerous useful tips, but also of vital information on safety, use and maintenance.

1.the machine should not be installed in an outdoor environment, not even when a roof shelters the area, because it may be very dangerous to leave it exposed to rain and thunderstorms.

2.It must only be used by adults and exclusively for washing clothes following the instructions provided in this manual.

3.Should it have to be moved, proceed with the help of two or three people and handle it with the utmost care. Never try to do this alone, because the appliance is very heavy.

4.Before loading the washer- dryer, make sure the drum is empty.

5.Never touch the washer- dryer when barefoot or with wet or damp hands or feet.

6.Never use extensions or multiple plugs, which are particularly dangerous in humid environments. The power supply cable must never be bent or dangerously compressed.

I only want an authorised specialised technician with original Indesit spare parts!

7.Never open the detergent dispenser while the appliance is functioning; do not use hand wash detergent because the abundance of foam could damage its internal parts.

8.Never pull on the supply cable or the washer-dryer to disconnect it from the wall socket: it is extremely dangerous.

9.While the appliance is functioning, do not touch the drain water as it could reach very high tempera- tures. The appliance door, during wash cycles, tends to become hot; ensure that children do no touch it. Never force the washer- dryer door because this could damage the safety lock which prevents accidental opening when the nachine is working. Allow a few minutes at the end of the program for the lock to release.

10.In case of malfunctioning, first close the water tap and unplug the appliance from the wall socket; do not under any circum- stances touch internal parts in order to attempt repairs.

How to change the power supply cable

The washing machine power supply cable is special and can be purchased exclusively from authorised Technical Service Centres.

To replace the cable:

1.Make sure that the machine is switched off and unplugged.

2.Remove the cover by unscrewing screws I [fig 13].

3.Disconnect the wires from the radio interference suppressor F [fig. 14] noting as to their position (Blue=N wire; Brown=L wire) leaving the earth wire until last .

N.B.: letters L, N and the symbol are indicated on the

radio interference suppressor.

4.Remove the screw and washer V [fig. 15], which act as a stop for the cable passageway.

5.Remove the upper part of the cable slightly from the back panel of the appliance, pull the power supply cable upwards and take it out [fig. 16].

To connect the new power supply cable, reverse the pro- cedure.

It is important for your safety that you reassemble all parts and screws used.

N

L

F

Fig. 13

Fig. 14

Fig. 15

Fig. 16

Instructions for installation and use 16

Image 17
Contents Washing machine Guide to understanding labels p Care and maintenance p Installation and removal pProblems and solutions p Technical characteristics pAt the end of the wash cycle What goes in your washer-dryer?Drying cycle knob Temperature control knobDetergent dispenser Easy iron60C 90C40C 50CAt the end of the drying cycle Now set the wash cycle knobUnderstanding labels Bleaching Ironing Dry cleaning DryingHow much does it weigh? 1 sheet 400-500 gr Watch the weightHolidays unplug the appliance Dungaree alertUseful tips about the detergent dispenser Programme selector knob keeps turning? Excessive vibration during the spin cycle Washer-dryer does not drain or spinWasher-dryer leaks Too much foamLevelling Replacement fuse coversConnection to the water mains Electric connectionRemoving the plug How to connect an alternati- ve plugEarth NeutralMagnet plate Hinge Supports Hinges MagnetRubber plug Accessories provided for the height adjustment Using the Drilling TemplateMounting the Parts onto the Face of the Machine Mounding the Parts onto the Wooden Panel DoorNever exaggerate with doses When in need, check the pump and the rubber hoseYour safety and that Stay in touch Instructions for installation and use Leader for young Europe