Indesit WD 12 X Washer-dryer does not drain or spin, Excessive vibration during the spin cycle

Page 11

Is the washer-dryer’s drain duct clogged? Is there an extension of the drain hose? If so, is it positioned incorrectly, blocking the water flow?

Is there space between the machine and adjacent units? If it is not a built-in model, the washer-dryer will oscillate a bit during the spin cycle. A few cm of space should therefore be left around it.

The washer-dryer does not drain or spin.

Does the selected programme incorporates water draining? Some programmes stop at the end of the wash cycles and draining will have to be selected manually.

Is the “Easy iron" function -where provided - enabled? This function requires manual selection for draining.

Is the drain hose kinked? The tract of the drain hose must be as straight as possible. Make sure the drain hose is not squashed or kinked.

Excessive vibration during the spin cycle.

Have all transit screws been removed durind instal- lation? See the following page on installation procedures.

Has the washer-dryer been levelled correctly? The levelling of the appliance

should be checked periodically. Adjust the feet and check them with a level.

The washer-dryer leaks.

Is the metal ring of the inlet hose properly attached? Turn off the water supply, unplug the appliance and try tightening its attachment without forcing it.

Is the detergent dispenser obstructed? Remove and wash it under tap water.

Is the drain hose well

Too much foam.

Is the detergent appropriate for machine washing? Check whether the definition on its label reads “for machine wash” or “hand and machine wash”, or any other similar wording.

Is the correct amount being used? An excessive amount of detergent, besides producing too much foam, does not guarantee a more effective wash, and causes scaling in the internal parts of the appliance.

The washer-dryer does not dry.

Check whether:

Always get

assistance from

authorised

technicians and always insist on original spare parts.

attached? Turn off the water supply, unplug the appliance and try tightening its attachment.

the plug has been correctly inserted into the socket; there is electricity in your home; the appliance door has been shut properly; a delayed start (if available) has not been selected; programme knob A has been set to position (Stop/Reset); the drying cycle knob C has been set to position 0.

Technical characteristics

Model

WD 12 X

 

Dimensions

width 59,5 cm

 

 

height 81,5 cm

 

 

depth 54 cm

 

 

 

Capacity

from 1 to 5,5 kg for the wash programme; from 1 to 4 kg for the drying programme

 

 

 

Electrical

voltage 230/240 Volt 50 Hz

 

connections

maximum absorbed power 2050 W

 

 

 

Water connections maximum pressure 1 MPa (10 bar)

 

 

minimum pressure 0,05 MPa (0,5 bar)

 

 

drum capacity 46 litre

 

 

 

 

Spinning speed

up to 1200 rpm

 

 

 

Control programs

wash: programme 3; temperature 60C°; carried out with 5 kg load;

in compliance with

drying: run with a load of 2.5 kg and knob C et to position

.

IEC regulation 456

 

 

This appliance conforms with the following E.E.C. directives:

-73/23/EEC of 19/02/73 (Low Voltage) and subsequent modifications

-89/336/EEC of 03/05/89 (Electromagnetic Compatibility) and subsequent modifications

The washer-dryer doesn't dry properly.

Check whether:

the end of the drain hose is underwater; the drain pump is obstructed; the advice given on the maximum loads has been taken; the water tap has been turned on.

If, despite all checks, the washer- dryer fails to function and the problem persists, call your nearest authorised Customer Service Centre, providing the following information:

-the nature of malfunction

-the model type no. (Mod. ....)

-the serial number (S/N ....) This information can be found on the data plate situated at the back of the washer-dryer.

Instructions for installation and use 10

Image 11
Contents Washing machine Technical characteristics p Installation and removal pGuide to understanding labels p Care and maintenance p Problems and solutions pAt the end of the wash cycle What goes in your washer-dryer?Easy iron Temperature control knobDrying cycle knob Detergent dispenser50C 90C60C 40CAt the end of the drying cycle Now set the wash cycle knobUnderstanding labels Bleaching Ironing Dry cleaning DryingDungaree alert Watch the weightHow much does it weigh? 1 sheet 400-500 gr Holidays unplug the applianceUseful tips about the detergent dispenser Programme selector knob keeps turning? Too much foam Washer-dryer does not drain or spinExcessive vibration during the spin cycle Washer-dryer leaksElectric connection Replacement fuse coversLevelling Connection to the water mainsNeutral How to connect an alternati- ve plugRemoving the plug EarthMagnet plate Hinge Supports Hinges MagnetRubber plug Mounding the Parts onto the Wooden Panel Door Using the Drilling TemplateAccessories provided for the height adjustment Mounting the Parts onto the Face of the MachineNever exaggerate with doses When in need, check the pump and the rubber hoseYour safety and that Stay in touch Instructions for installation and use Leader for young Europe