Samsung DV331AG, DV331AE user manual Wire system connections

Page 20

installing your dryer

6.Review Gas Requirements section. Remove the pipe thread protective cap.

Apply pipe joint compound or about 1 1/2 wraps of Teﬂ on tape over all threaded connections. Pipe joint compound must be resistant to the action of any liqueﬁ ed petroleum gas.

Connect the gas supply to your dryer.

An additional ﬁ tting is required to connect the 3/4” (1.9 cm) female thread end of a ﬂ exible connector to the 3/8” (1 cm) male threaded end on the dryer.

Securely tighten the gas line ﬁ tting over threads.

Turn on the gas supply. Check all gas connections for leaks using a soap solution. If bubbles appear, tighten the connections and recheck.

DO NOT use an open ﬂ ame to check for gas leaks.

3-WIRE system connections

1.Loosen or remove the center terminal block screw.

2. Connect the neutral wire (white or center wire) of the power cord to the center, silver-colored terminal screw of the terminal block. Tighten screw.

3. Connect the other wires to outer terminal block screws. Tighten screws.

4.Tighten the strain relief screws.

5.Insert the tab of the terminal block cover into your dryer’s rear panel slot.

Secure the cover with a hold-down screw.

1.External ground connector

2.Neutral grounding wire (green/yellow)

3.Center silver-colored terminal block screw

4.Neutral wire (white or center wire)

5.3/4” (1.9 cm) UL-listed strain relief

If converting from a 4-wire electrical system to a 3-wire, the ground strap must be WARNING reconnected to the terminal block support to ground the dryer frame to the neutral

conductor.

20_ installing your dryer

DV331AE-03026A-01_EN.indd Sec5:20

2011-03-28 12:18:05

Image 20

Contents Gas and Electric Dryer Features Safety instructions What YOU Need to Know about Safety InstructionsImportant Safety Symbols and Precautions DeathRead all instructions before using this appliance What to do if YOU Smell GAS California Safe Drinking Water and Toxic Enforcement ACT Contents See Dryer Exterior Installing your dryerTools Needed for Installation Weather Hood Type Recommended Ducting RequirementsElectric and GAS Dryer Location Considerations Important to InstallerAlcove or Closet Installation With optional pedestal base or stacking kit Required Dimensions for Installation With PedestalRequired Dimensions for Installation With Stacking Kit Mobile Home Installation ExhaustingUnited States CanadaCommonwealth of Massachusetts installation instructions GAS RequirementsElectrical Requirements GroundingGas models Electric modelsElectrical Connections Gas models U.S. and CanadaElectric models U.S. only Electric models Canada OnlyConnecting the Inlet Hose Method1 Method2 Tools and Parts Replacement Parts and AccessoriesInstallation Models Wire system connections Final Installation Checklist GAS Models ONLY- DV331AGDryer Exhaust Tips Don’t let a poor exhaust system slow drying byDoor Reversal Operating Instructions, tips Overview of the Control PanelWhen the cycle is complete, a chime will sound Signal SelectionDigital Graphic Display Dry Level Selection ButtonSelect Cycle Option Setting/Releasing Setting & releasingChild Lock Drum LightRack Dryoptional Installing the drying rackSuggested Items Suggested TEMP. Settings Getting Started Clean the Lint FilterLoad the Dryer Properly Care and cleaning Things to Avoid Special laundry tipsSpecial Laundry Tips Check These Points if Your DRYER… TroubleshootingProblem Solution Lter during the cycle Error Display Meaning Solution Information CodesWash Cycle Special Instructions Laundering Fabric Care ChartAppendix Declaration of Conformity SpecificationsProtecting the Environment Cycle Chart TimeWarranty Samsung Dryer Limited Warranty to Original PurchaserTo obtain warranty service, please contact Samsung at Questions or COMMENTS?