Electrolux 16820 manual Permanent connection

Page 55

Installation

If you fit your own plug, the colours of the wires in the mains lead of your appliance may not correspond with the markings identifying the terminals in your plug, proceed as follows:

Connect the green and yellow (earth) wire to the terminal in the plug which is marked with the letter «E» or the earth symbol or coloured green and yellow.

Connect the blue (neutral) wire to the terminal in the plug which is marked with the letter «N» or coloured black.

Connect the brown (live) wire to the terminal in the plug which is marked with the letter «L» or coloured red.

The plug moulded on to the lead incorporates a fuse. For replacement, use a 13 Amp BS1363 fuse. Only ASTA or BSI approved fuses should be used.

The plug must not be used if the fuse cover/carrier is lost. The cover/carrier is indicated by the coloured insert at the base of the plug.

A replacement cover/carrier must be obtained from your local AEG Service Centre.

The power supply cable must be easily accessible after installing the machine.

Permanent connection

In the case of a permanent connection it is necessary that you install a double pole switch between the appliance and the electricity supply (mains), with a minimum gap of 3 mm between the switch contacts and of a type suitable for the required load in compliance with the current electrical regulations.

The switch must not break the yellow and green earth cable at any point.

This operation should only be performed by a qualified electrician.

55

Image 55

Contents Lavamat Dear customer Contents Automatic washing and drying NON-STOP programme Programme charts wash and special programmesPage General safety Safety instructionsInstallation During use Child safetyMachine DisposalTips for environmental protection Packaging materialsMain features of your washer-dryer Front view Description of the applianceProgramme selector dial Control panelPosition 40C Easy iron Programme Option buttonsPosition Cold = cold wash Start START/PAUSE buttonPause Display Delay Timer buttonElectronic Drying button Drying Time buttonProgramme progress display Cancelling a programmeAltering a programme which is running Opening the door after the programme has started Before the first wash Detergent dispenser drawerSorting out and preparing the laundry Preparing the wash cycleSynthetics Sort of laundry Approximate Dry weightsTypes of fabric and care labels CottonDelicates 40 Which detergent? Detergents and additivesTraditional Powders Which form?Sort of laundry Preparing the drying cycleLoad Garments not suitable for dryingFibre residue Drying symbols on garment labelsDuration of the drying cycle Modification of the drying time or degree of dryingAdd detergent and additive How to washMax. load Load the laundrySelection of the desired options Selection of the desired wash programmeSelection of the Rinse + extra rinse option Selection of the Delay Timer optionStarting the programme At the end of the programme Drying only Max. load How to dryAutomatic washing and drying NON-STOP programmeWash programmes Programme chartDescrip Special programmesMax Consumption Tion Drying time Spin speed Mins 1600 Timed DryingDegree of drying Max. loadMax Water Energy Duration Load Litres KWh Minutes Consumption data for timed dryingAfter each wash Cleaning and maintenanceMaintenance Wash Periodical cleaning ExteriorDrain pump Door sealEmergency emptying out Water inlet filterTroubleshooting Frost precautionsSomething not working? Water inlet hose is Problem Possible causeProblem Possible cause Solution E10 DistributedWhite residue is left on the laundry Unsatisfactory washing resultsIf grey stains remain on the laundry Foam is still visible even after the last rinseThis appliance complies with the following EC directives Technical dataService & Spare Parts Service & Spare Parts08705 929 Customer care Help us to help youExclusions Standard Guarantee ConditionsEuropean Guarantee Page Front view and side view Dimensions of the applianceRear view Two plastic bags InstallationUnpacking Remove the polystyrene block fromPositioning Installation on a suspended floorLevelling Into a drainage standpipe Water inlet cold water connection onlyWater drainage Do not connect to a hot water supplyOnto a sink outlet spigot Electrical connections Interest of the environmentPermanent connection Electrolux plc