Blomberg WNF 8441 AE20 user manual Installation, Appropriate installation location

Page 9
WARNING: Do not remove the transportation locks before taking out the packaging reinforcement.

3Installation

Refer to the nearest Authorised Service Agent for installation of the product. To make the product ready for use, review the information in the user manual and make sure that the electricity, tap water supply and water drainage systems are appropriate before calling the Authorized Service Agent. If they are not, call a qualified technician and plumber to have any necessary arrangements carried out.

C Preparation of the location and electrical, tap water and waste water installations at the place of installation is under customer's responsibility.

B WARNING: Installation and electrical connections of the product must be carried out by the Authorized Service Agent. Manufacturer shall not be held liable for damages that may arise from procedures carried out by unauthorized persons.

A WARNING: Prior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products cause risks for your safety.

C Make sure that the water inlet and discharge hoses as well as the power cable are not folded, pinched or crushed while pushing the product into its place after installation or cleaning procedures.

3.1 Appropriate installation location

Place the machine on a rigid floor. Do not place it on a long pile rug or similar surfaces.

Total weight of the washing machine and the dryer -with full load- when they are placed on top of each other reaches to approx. 180 kilograms. Place the product on a solid and flat floor that has sufficient load carrying capacity!

Do not place the product on the power cable.

Do not install the product at places where temperature may fall below 0ºC.

Place the product at least 1 cm away from the edges of other furniture.

3.2Removing packaging reinforcement

Tilt the machine backwards to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

3.3Removing the transportation locks

A

A WARNING: Remove the transportation safety bolts before operating the washing machine! Otherwise, the product will be damaged.

1.Loosen all the bolts with a suitable spanner until they rotate freely (C).

2.Remove transportation safety bolts by turning them gently.

3.Attach the plastic covers supplied in the User Manual bag into the holes on the rear panel. (P)

Washing Machine /User’s Manual

9 / EN

 

 

Image 9
Contents Washing Machine WNF 8441 AE20 Important information or useful hints about usage Dear Customer Explanation of symbolsInstallation Important instructions for safety Environment4Maintenance and cleaning TroubleshootingGeneral safety Important instructions for safety and environmentUnplug the product when not in use Service life of your product is 10 yearsCompliance with Weee Directive Package informationDisposing of the waste product Your washing machine Power cableOverview Top panel Loading door Control panelYour washing machine Package Contents Stand-by mode power W Off-mode power W Main model code Your washing machine Technical specificationsModels EN Spin speed rpm/ min., maxAppropriate installation location InstallationRemoving packaging reinforcement Removing the transportation locksInstallation Connecting water supplyConnecting to the drain 11 / EN Adjusting the feetInstallation Electrical connection Fitting a different plug12 / EN 13 / EN Preparation Sorting the laundry14 / EN Initial use Preparation Preparing laundry for washingThings to be done for energy saving 15 / ENUsing detergent and softener Preparation Correct load capacityLoading the laundry Preparation Adjusting detergent amountUse different detergents for coloured and white laundry 17 / ENUsing bleaches Using starchDo not use softener and starch together in a washing cycle Do not use bleaching agent and detergent by mixing them19 / EN Preparation Tips for efficient washingDisplay symbols Operating the productControl panel Operating the product Preparing the machine Programme selectionMain programmes Operating the product Additional programmes Operating the product Special programmes Temperature selectionSpin speed selection 23 / EN24 / EN Operating the product Programme and consumption tableOperating the product 25 / ENOn the panel Prewash Operating the product Auxiliary function selectionRinse Plus 26 / ENTime display Progress of programme Operating the product Starting the programmeLoading door lock Changing the selections after programme has startedMachine is in Rinse Hold mode Cancelling the programmeChild Lock End of programme30 / EN Your machine is equipped with a Standby Mode31 / EN Quick User GuideCleaning the detergent drawer Cleaning the loading door and the drumMonths Cleaning the water intake filters Maintenance and cleaningCleaning the body and control panel Draining remaining water and cleaning the pump filterInstall the filter Pull the emergency draining hose out from its seat34 / EN 35 / EN TroubleshootingProgramme cannot be started or selected Machine does not fill with water36 / EN TroubleshootingIt does not rinse well 37 / ENDetergent residue in the detergent drawer 38 / ENWater pressure is low. Check the water pressure Foam is overflowing from the detergent drawerLoading door may be open. Close the loading door On / Off button might not be pressed. Press On / Off button39 / EN Machine does not start. Nothing appears on the display40 / EN Complying Commission Delegated Regulation EU No 1061/201

WNF 8441 AE20 specifications

The Blomberg WNF 8441 AE20 is a cutting-edge washing machine that combines efficiency, advanced technology, and user-friendly design. This model stands out in the market due to its impressive features that cater to the needs of modern households.

One of the main features of the WNF 8441 AE20 is its energy efficiency. It boasts an A+++ energy rating, which means it consumes significantly less energy compared to traditional washing machines. This not only helps reduce electricity bills, but it also supports environmentally friendly practices by minimizing carbon footprints.

The washing machine offers a generous 8 kg load capacity, making it suitable for families of various sizes. Its versatile drum is designed to handle different fabric types, ensuring optimal care for all your washing needs. The WNF 8441 AE20 comes equipped with a variety of washing programs, including quick wash options, eco-friendly cycles, and delicate settings for more fragile items. This flexibility allows users to select the most appropriate setting based on their laundry requirements.

Another notable feature of this washing machine is its innovative ProSmart Inverter Motor. This technology enhances the overall performance while reducing noise levels significantly. Users can expect quiet operation, making it ideal for homes where laundry is done at any time of day or night without disturbing family members.

The machine is designed with user convenience in mind, featuring a large LED display that provides clear information about the selected programs and remaining time. The control panel is intuitive, making it easy for users of all ages to operate the machine without confusion. Additionally, the Delay Start function allows users to schedule washes at their convenience, taking advantage of off-peak energy hours.

In terms of safety and maintenance, the Blomberg WNF 8441 AE20 is equipped with a Self-Cleaning Detergent Drawer that ensures optimal performance while keeping the machine clean and free from mold and bacteria. It also features a child lock function, adding an extra layer of safety for households with young children.

Overall, the Blomberg WNF 8441 AE20 is a highly advanced washing machine that combines performance, efficiency, and convenience. With its array of features and innovative technologies, it stands as a reliable choice for those seeking to enhance their laundry experience while being mindful of energy consumption and care for their garments. It represents the perfect blend of practicality and modern design for any home.