Ariston ARMF 125 manual Installation, Unpacking and levelling

Page 2

Installation

￿ This instruction manual should be kept in a safe

GB

place for future reference. If the washer-dryer is sold,

 

 

transferred or moved, make sure that the instruction

 

manual remains with the machine so that the new

 

owner is able to familiarise himself/herself with its

 

operation and features.

 

￿ Read these instructions carefully: they contain vital

 

information relating to the safe installation and

 

operation of the appliance.

 

Unpacking and levelling

 

Unpacking

 

1. Remove the washer-dryer from its packaging.

 

2. Make sure that the washer-dryer has not been

 

damaged during the transportation process. If it has

 

been damaged, contact the retailer and do not

 

proceed any further with the installation process.

 

3. Remove the 4

 

protective screws (used

 

during transportation) and

 

the rubber washer with

 

the corresponding

 

spacer, located on the

 

rear part of the appliance

 

(see figure).

4.Close off the holes using the plastic plugs provided.

5.Keep all the parts in a safe place: you will need them again if the washer-dryer needs to be moved to another location.

￿Packaging materials should not be used as toys for children.

Levelling

1.Install the washer-dryer on a flat sturdy floor, without resting it up against walls, furniture cabinets or anything else.

2. If the floor is not perfectly level, compen- sate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2°.

Levelling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise and prevent it from shifting while it is operating. If it is placed on carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washer-dryer.

Connecting the electricity and water supplies

Connecting the water inlet hose

1. Insert seal A into the end of the inlet hose and screw the latter onto a cold water tap with a 3/4 gas threaded opening

 

 

A

(see figure).

 

 

 

 

 

 

Before performing the

 

 

 

connection, allow the

 

 

 

 

 

 

water to run freely until it

 

 

 

is perfectly clear.

 

 

 

2. Connect the inlet hose

 

 

 

 

 

 

to the washer-dryer by

 

 

 

screwing it onto the

 

 

 

corresponding water inlet

 

 

 

of the appliance, which is

 

 

 

situated on the top right-

 

 

 

hand side of the rear part

 

 

 

of the appliance (see

 

 

 

figure).

 

 

 

 

3. Make sure that the hose is not folded over or bent.

￿The water pressure at the tap must fall within the values indicated in the Technical details table (see next page).

￿If the inlet hose is not long enough, contact a specialised shop or an authorised technician.

￿Never use second hand hoses sets. Do not reuse hose sets from any previously installed washing machine.

￿Use the ones supplied with the machine.

2

Image 2
Contents Instructions for use Washer -DRYERUnpacking and levelling InstallationConnecting the electricity and water supplies Technical data First wash cycleDescription of the washer-dryer and starting a wash cycle Control panelIndicator lights Wash cycles Table of wash cyclesPersonalisation Setting the temperatureSetting the drying cycle FunctionsDetergents and laundry Precautions and tips General safetyDisposal Opening the porthole door manuallyCare and maintenance Possible causes / Solutions TroubleshootingProblem Service Ariston Genuine Accessories Priority Service Spare PartsPage Page 195068194.02