Zanussi 132985450 manual Building-in, Preparation and assembly of the door

Page 28

132985450.qxd 18/07/2005 17:47 Pagina 28

Building-in

This appliance has been designed to be built into the kitchen furniture.

The recess should have the dimensions shown in picture

A.

 

 

 

 

 

 

600

 

 

 

 

 

 

600

 

 

 

 

.

 

 

5

96

min

 

515

570

 

176,5

 

 

min

818

416

120

820

 

 

541

195

 

 

8

 

 

 

 

 

 

 

160

 

 

165

90

 

 

90

A

P0965

4

 

 

When installing the appliance into the kitchen furniture ensure, if possible, the hoses are placed in either of the two recesses on the back of the appliance. This will help to prevent the hoses from becoming kinked or trapped. Picture AB.

Preparation and assembly of the door

The machine is originally pre-arranged for the assembly of a door opening from right to left.

In this case it is sufficient to screw in the hinges (1) and the counter-magnet (6) provided with the appliance, at the right level (Fig. B).

6

 

 

4

 

 

 

1

2

7

5

1

 

 

3

 

23

 

 

B

P0982

 

 

 

a) Door

The dimensions of the door should be:

- width 595-598 mm - thickness 16-22 mm

The height (C-Fig. C) depends on the height of the adjacent furniture's base.

35 Ø 12.5-14 depth

 

 

16

 

B

 

-

 

 

22

 

 

 

 

416

C

 

 

22+1,5

 

 

-598

 

 

 

595

 

P0422S

 

 

C

b) Hinges

To mount the hinges it is necessary to drill two holes (dia. 35 mm, depth 12.5-14 mm depending on the depth of door furniture) on the inner side of the door. The distance between the holes hobs fixing centres must be 416 mm.

The distance (B) from upper edge of the door to the centre of the hole depends on the adjacent furniture's dimensions.

The required dimensions are given in the picture C. The hinges will be fixed to the door by means of screws for wood (2-Fig. B) supplied with the appliance.

c) Mounting the door

Fix the hinges (1) to the machine by means of the M5x8 screws (3-Fig. B). The hinges can be adjusted to compensate for possible uneven thickness of the door. To align the door perfectly it is necessary to loosen the screw (3-Fig. B), adjust the door and tighten the screw again.

d) Counter-magnet (6)

The appliance is pre-arranged for a magnetic closure of the door. To enable a correct operation of this device, it is necessary to screw the counter-magnet (6) (steel disk + rubber ring) into the inner side of the door.

Its position must correspond to the magnet (4) on the appliance (see picture D).

 

6

 

4

P0984

D

 

28

Image 28
Contents Washing Machine Important Safety Information InstallationChild Safety UseContents Ecological hints Your New Washing MachineInterest of the environment Description of the Appliance Child safety featureDetergent dispenser drawer Control Panel Delay Start button Quick Wash buttonSuper Rinse button Easy Iron buttonDelayed start Programme progress displayProgramme selector dial End of programmeAltering an option or a running programme Interrupting a programmeProgramme information Switch the machine on Operating SequenceLoad the laundry Select the required programmeSelect the Delay Start Select the required optionsStart the programme At the end of the programme«JETSYSTEM» wash 1000g = 1 kgWhich detergent? Which form?Wash Care Symbols Important NotesWashing Programmes Special Programmes Programme Programme description Functions LoadMaintenance and Cleaning Emergency emptying out Water inlet filterSomething Not Working Symptom Possible causes Service & Spare Parts0870 5 Guarantee Conditions European guaranteeThis guarantee does not cover Customer Care DepartmentInstallation Instructions Technical SpecificationsUnpacking PositioningWater inlet Appliance must be connected to a cold water supplyInto a drainage standpipe Water drainageOnto a sink outlet spigot Levelling Special conditionsElectrical connection Permanent connectionPreparation and assembly of the door Building-inDrill four fixing holes see Fig. G From the Electrolux Group. The world’s No choice