GE SPBD880 Prepare the Pedestal, Level the Washer, Reinstall the Drawer, Remove Shipping Screws

Page 13

Installation Instructions

2PREPARE THE PEDESTAL

A

Pull the

Connectors

 

drawer out

 

 

as far as it

 

 

will go.

 

B

Remove

 

 

the screws

 

 

from the

 

 

drawer

 

 

slides. Detach the wiring connector and the

 

hose connector at the back of the drawer.

 

Slide the drawer out of the base and set aside.

CRemove the screws from the service panels at the rear of the pedestal and place the panels within the pedestal.

Remove screws from service panels

3INSTALL THE PEDESTAL TO THE WASHER

APlace the pedestal against the bottom

of the unit. Check to be sure the drawer front is at the front of the unit.

BAlign the holes in the pedestal with the holes in the bottom of the unit. Use a Phillips screwdriver to install the 4 screws through the front of the pedestal and through the rear panels and into the unit—do not tighten.

CSlide the pedestal toward the unit, until it is aligned front to back. Use an 8 mm socket wrench to securely tighten the screws.

DReplace the service panels on the back and tighten the screws.

4LEVEL THE WASHER

AStand the washer upright. Move it close to its final location.

BMake sure that the washer is level by placing a spirit level on top. Check side to side and front to back.

CUse an open-ended wrench to adjust

the legs in and out. Tighten the locknut against the bottom of the pedestal.

NOTES:

To minimize vibration, the locking nuts must be tight.

To reduce vibration, ensure that all four rubber leveling legs are firmly touching the floor. Push and pull on the back right and then back left of your washer.

5REINSTALL THE DRAWER

ACheck to be

sure the slides Connectors are closed.

B Slide the drawer into the opening.

Align the drawer

supports to

the slides on each side.

COpen the drawer fully. Reattach the hose connector and wiring connector at the rear of the drawer. Make sure both connections are secure.

DReinstall the original screws into each drawer slide. Tighten both screws. The drawer should slide smoothly when you push it closed.

6REMOVE SHIPPING SCREWS

Remove the 4 shipping screws, plastic support tubes and rubber grommets on the back side of the washer.

13

Image 13
Contents Operating Instructions Installation InstructionsConsumer Support Manual del propietario InstalaciónInstallation Instructions Tips Operating Instructions Safety InstructionsKeep the area underneath and around your Appliances free of combustible materials such asTroubleshooting Tips Consumer Support Instructions Operating Instructions InstallationGe.com About the washer control panel PowerSmartDispense feature allows you to set your liquid About the SmartDispense pedestal featuresSmartDispense Select your desired Wash CyclePress the Power button Press the Settings button Setting Your Water Hardness LevelDetermine the Hardness of Your Tap Water Water Hardness Test Strip IndicationInstruction Panel Instructions InstallationDetergent Tanks Fabric Softener TankDispense Level Concentration LevelTo Fill Your Detergent Tank Using the SmartDispense pedestalSmartDispense system To recognize that it has been filledTo Fill Your Fabric Softener Tank Support SafetyAdjacent tank KIT Contents Installation PreparationTools YOU will Need Remove the Leveling LegsPrepare the Pedestal Reinstall the DrawerLevel the Washer Remove Shipping ScrewsAttach the Hose Connectors and Electric Connectors Finalize the InstallationSafety Instructions Operating Instructions Before you call for service…ge.comOperating Instructions Safety Instructions Installation Before you call for service…We’ll Cover Any Appliance. Anywhere. Anytime Consumer Product Ownership Registration Ownership Registration Page What Is Not Covered in the United States SafetyOperating For The Period Of We Will ReplaceInstructions Safety Instructions GE SmartDispense Pedestal Warranty. For customers in CanadaWhat Is Not Covered in Canada OperatingInstallation Instructions Instructions Safety InstructionsFonctionnement Mesures de sécurité Fonctionnement InstallationSoutien au consommateur Et les connecteurs électriquesOu avec tout autre appareil électroménager Conseils de dépannageEt sachez mettre en oeuvre Sécurité Fonctionnement InstallationPower Alimentation Fonctionnement Mesures de sécurité InstallationLe panneau de contrôle de votre laveuse Sélectionnez le cycle de lavage La fonction SmartDispense vous permet de réglerUtilisez les flèches gauche et droite De lessiveRégler le niveau de dureté de l’eau Propos des fonctions du socle SmartDispenseDéterminer la dureté de l’eau du robinet Indication de la bande de test de la dureté de l’eauLe tableau d’instructions Mesures de sécurité FonctionnementLes réservoirs à lessive Le réservoir à adoucissantMesures de SécuritéNiveau de concentration Niveau de distributionPour remplir le réservoir à lessive Utilisation du socle SmartDispenseMesures Remarque Ne remplissez pas Pour remplir le réservoir AdoucissantAu système SmartDispense Nouveau rempli. Après avoir rempliNettoyer les réservoirs Installation Conseils de dépannageAdoucissant et à lessive De SmartDispensePréparation a L’INSTALLATION Outils Nécessaires Pour Installer LE SocleContenu DU KIT Retirer LES PiedsPréparer LE Socle Réinstaller LE TiroirNiveler LA Laveuse Retirer LES VIS DE TransportConfirmation D’INSTALLATION Terminer L’INSTALLATIONAvant d’appeler un réparateur… Lorsque votre lave-linge détecte pour la première fois Problème Causes possibles CorrectifsLe lave-linge détecte la taille Tourner au début De la charge de linge dansSmartDispense a développé Concentrés La capteur d’adoucissantPage Pour une période de Nous remplacerons Garantie de socle GE SmartDispenseCe qui n’est pas couvert Un anProlongation de garantie Soutien au consommateur Service de réparationsConsejos para la InstruccionesDe instalación Consejos para solución de problemasInstrucciones Mantenga las zonas debajoSoporte al consumidor AL Usar EL Pedestal SmartdispenseEl panel de control de la lavadora Power EncendidoInstrucciones De seguridad Instrucciones De instalación Consejos para laDe seguridad Instrucciones Acerca de las funciones del pedestal SmartDispenseNota Cuando use SmartDispense Cómo configurar el nivel de dureza del agua Consejos para la solución de problemasDetermine la dureza del agua del grifo Para calibrar la dureza del aguaDe seguridad Instrucciones De instalación InstruccionesEl panel de instrucciones Los tanques de detergenteNivel de dispensado Nivel de concentraciónSoporte alconsumidor Cómo usar el pedestal SmartDispenseNota No llene el tanque mientras Para llenar el tanque de suavizante para la ropaInstalar al sistema SmartDispense Soporte al ConsumidorPreparación Para LA Instalación Contenido DEL KITRetire LAS Patas DE Nivelación Instrucciones para uso del inspector localNivele LA Lavadora Prepare EL PedestalReinstale LA Gaveta Retire LOS Tornillos DEL EnvíoFinalice LA Instalación LOS Conectores EléctricosDe instalación Instrucciones Antes de llamar al servicio de asistencia técnica…Instalación Instrucciones De seguridad FuncionamientoDe suavizante líquido Del suavizante para la ropa y enjuague el tanqueDe suavizante antes de llenarlo nuevamente con Líquido concentrado para la ropaGarante General Electric Company. Louisville, KY Período Se sustituiráUn año La pieza defectuosaSolicite una reparación Soporte al consumidor Página Web de GE AppliancesGarantías ampliadas Piezas y accesoriosGE Appliances Website Consumer Support
Related manuals
Manual 64 pages 1.46 Kb

SPBD880 specifications

The GE SPBD880 is an innovative and advanced circuit breaker designed to meet the demands of modern electrical systems. With a strong focus on safety, reliability, and efficiency, this model stands out in the market.

One of the main features of the SPBD880 is its ability to provide exceptional protection against overload and short-circuit conditions. This is essential in preventing damage to electrical equipment and ensuring the safety of personnel. The SPBD880 employs thermal-magnetic trip units, which combine both thermal and magnetic operating principles. This dual functionality allows for precise control and rapid response to abnormal conditions, enhancing the overall safety of the electrical system.

In addition to its robust protection mechanisms, the SPBD880 is designed for ease of use and installation. With a compact design, the breaker can fit into tight spaces, making it suitable for various applications, including industrial and commercial environments. The intuitive mounting system simplifies the installation process, reducing labor costs and installation time.

The SPBD880 also features advanced communication capabilities. It is equipped with integrated metering and monitoring technologies, allowing for real-time data collection on energy usage and system performance. This data can be invaluable for predictive maintenance practices and optimizing energy consumption, leading to reduced operational costs.

Another notable characteristic of the SPBD880 is its adaptability. It can be configured to accommodate varying system requirements, ensuring that it meets specific application needs. Whether in a standalone setup or part of a larger automated electrical system, the SPBD880 can seamlessly integrate with other devices to enhance functionality.

The environmentally friendly design of the GE SPBD880 ensures minimal impact during manufacturing and implementation. With a focus on sustainability, it utilizes materials and technologies that reduce the overall carbon footprint.

In summary, the GE SPBD880 circuit breaker combines advanced safety features, ease of use, and adaptability, making it an excellent choice for modern electrical installations. Its innovative design not only enhances protection but also promotes efficiency and sustainability, positioning it as a vital component in both industrial and commercial settings. As electrical systems evolve, the SPBD880 offers the reliability and performance needed to keep pace with technological advancements.