LG Electronics TD-V10247G manual Pedestal Installation Instructions, Pedestal accessory includes

Page 17

Part 4 ACCESSORIES INSTALLATION

Pedestal Installation Instructions

The pedestal accessory includes:

• Drawer divider (1)	•	Wrench (1)
• Screws (18) †	•	Retainers (4) ††

3 Place the dryer on the pedestal. Make sure the front and back feet are in the correct positions. The dryer feet will fit into the innermost positions as shown.

For dryer

For washer/combo

† Dryer installation only uses 8 screws †† For dryer only

Tools Needed for Installation:

• Phillips-head screwdriver

• Wrench (supplied)

To ensure safe and secure installation, please thoroughly follow the instructions below.

1 To set the dryer to the same height as the washer, fully retract the leveling feet of the dryer by turning them counterclockwise, then turn them clockwise 1-1/2 turns.

NOTE: The appliance and pedestal assembly must be placed on a solid, sturdy, level floor for proper operation.

Retract fully	Then loosen
	1-1/2 turns

2 Insert the T-clip of the 4 retainers into the dryer base as shown. Press up on the back of the clip and pull outward to lock into place.

T-clip

Retainer

4 Make sure the screws on the pedestal align with the holes in the retainers, then install 4 screws at each corner to securely attach the appliance to the pedestal.

NOTE: If the screws are not installed properly, noise and vibration may result.

Move the appliance to the desired location.

5	Loosen the locknuts on all 4 leveling feet of the
	pedestal until you can turn them with the wrench.
	Turn clockwise to raise or counterclockwise to lower

until the pedestal is level and all 4 feet are solidly against the floor.

Raise

Lower

6 Securely tighten all locknuts by hand.

NOTE: Noise and vibration may result if locknuts are not tightened.

Be sure to connect the appliances to all water, power, or gas lines and draining or venting connections before operation.

If there is excessive vibration during the first operation after installation, slightly adjust the leveling feet.

Locknut

1 7

Image 17

Contents TD-V10247G TD-V14247E TD-V14247G Table of Contents Accessories Part 1 SpecificationsSeeking Warranty Service Part 2 Important Warranty and Safety InstructionsRead ALL Instructions Before USE Basic Safety PrecautionsGrounding Instructions What to do if YOU Smell GAS Safety Instruction for Installation Exhaust/Ducting Safety Instruction for InstallationSafety Instruction for Connecting Electricity Positioning the Dryer Part 3 Initial Steps for Installing Your DryerReversing the Door Procedure forDoor and latch should be aligned at the center when closed Venting System Connecting the ExhaustElectrical Plug Connections If changing the orifice, also adjust the gas valveConnection of Gas Supply Operation Preparation of the DryerConfirming Heat Source Dryer AirflowStacking Kit Installation Instructions Part 4 Accessories InstallationPedestal accessory includes Pedestal Installation InstructionsInstructions for Grounding of your Electric Dryer Part 5 Electrical Requirements for Electric DryersWire connection Direct wire Wire directOption 1 4-wire connection with a power supply cord Connection Option 2 3-Wire connection with a power supply cordOption 3 Optional 3-wire Electrical Requirements for Your Dryer Part 6 Electrical Requirements for GAS DryersVolt, 60 Hertz, with 3-Prong Grounding Plug Part 7 GAS Requirements and Instructions Exhaust Requirements and Instructions Part 8 Exhaust Requirements and MaintenanceCleaning the Lint Screen Exhaust and Dryer MaintenancePart 9 Operating Your Dryer Power ButtonFire Hazard Explosion HazardSensor Dry Temp Time Cycles Load Type Minutes Cycle SelectionManual Dry Temp Cycles Load Type MinutesTime Change Button Custom ProgramLED Display Estimated Time RemainingBeeper Option ButtonsTime Dry Temp. ControlType of Load Default Time Minutes When Using Air DryDry Level Start / Pause ButtonClean the door and its opening Drying will continue from where the cycleQuestion What to Do Part 10 Troubleshooting GuideTE1 TE2Problem There Is Lint On My Clothes Troubleshooting Guide TD-V10247G TD-V14247E TD-V14247G Contenido Accesorios Parte 1 EspecificacionesBúsqueda DE Asistencia Sobre LA Garantía Parte 2 Garantía E Instrucciones DE Seguridad ImportantesGuarde Estas Instrucciones Precauciones Básicas DE SeguridadInstrucciones Para LA Toma a Tierra QUÉ a Hacer SI Huele GAS Instrucción DE Seguridad Para LA Instalación Escape/Conducto Instrucción DE Seguridad Para LA Conexión DE Electricidad Debería asegurar las patas niveladoras SecadoraPaso 1 Colocación de la Procedimiento para Invertir la PuertaPaso 3 Conexión del Sistema de Escape y Ventilación AdvertenciaConecciòn Elèctrica Paso 4 Conexión del Suministro de GasPaso 6 Preparación de la Paso 8 Flujo de AireConfirmación de la Fuente de Calor en Secadoras a Gas Confirmación de la Fuente de Calor en Secadoras EléctricasInstrucciones de Instalaciòn para montar el Kit Parte 4 Instalaciòn DE AccesoriosEl accesorio de pedestal incluye Instalacion de la secadora Cinta de tipo doble-caraAdvertencia Tomacorriente de 3-alambres Tipo Nema 10-30R Cables directosConexiòn de 4-cables Cableado directo Opción 1 Conexión de 4-alambres con Conexiòn de 3-cables Cable DirectoSección AlambresOpción 3 Conexión Opcional de Requerimientos Eléctricos para su Secadora Parte 6 Requerimientos Eléctricos Para Secadoras a GASInstrucciones y Advertencias Parte 7 Requerimientos E Instrucciones Sobre EL GASRequerimientos e Instrucciones del Escape Parte 8 Requerimientos Y Mantenimiento Sobre EL EscapeLimpieza de la Malla de Pelusa Botón de encendido Parte 9 Usando SU SecadoraPeligro de Explosión Peligro de IncendioMinutos Selección del cicloTiempo Botón de cambio de tiempo FavoritoLa Pantalla de LED Tiempo rest. estimadoBotones Opción AlarmaTiempo de Secado Control tempArranque de seu secadora Nivel de Secado11 Botón de arranque / pausa Limpiar el filtro atrapapelusa MantenimientoPregunta Qué Hacer TE1 Parte 10 Guía Para LA Solución DE ProblemasPregunta Qué Hacer Parte 10 Guía Para LA Solución DE Problemas