Front Load Dryer Specifications

Front Load Dryers

FASG7073L R / N / A / W 7.0 Cu. Ft. Gas

•Product Shipping Weight (approx.) – 140 Lbs.

•An electrical supply with grounded three-prong receptacle is required. The power supply circuit must be installed in accordance with current edition of National Electrical Code (ANSI/NFPA 70) and local codes & ordinances. (Do not use same circuit as washer.)

•Voltage Rating – 120V / 60 Hz / 15 Amps

•Amps @ 120 Volts = 7 Amps

•Connected Load (kW Rating) @ 120 Volts = 0.5 kW

•Equipped with 120V 3-wire power supply cord, approx. 60" long.

•Always consult local and national electric, gas & plumbing codes.

•Can be installed alone, with or without optional 15" Drawer Pedestal, or stacked above matching Frigidaire® Affinity Washer, which requires installation of optional Dryer Stacking Kit. (For installation details, refer to instructions included with optional pedestal or stacking kit or on web.)

•Can be built in with matching Frigidaire® Affinity Washer in under- counter, recessed or closet installation. (Refer to Built-In Installations on this page for cutout dimensions. For additional installation details, refer to Product Installation Guide on web.)

•Closet installation requires vented door with 2 unobstructed louvered openings, minimum 60 sq. in. each, located 3" from top and bottom of door. Full-length 120 sq. in. opening also acceptable. Allow additional 1" clearance between fronts of units and closed door.

•Do NOT install in area exposed to dripping water or outdoor weather conditions; where gasoline or other flammables are kept or stored; or where dryer comes in contact with curtains, drapes or anything that will obstruct flow of combustion and ventilation air.

•For garage installation, dryer MUST be located minimum 18" above floor.

•Floor MUST be solid with 1" maximum slope. Do NOT install on carpeted surface.

•Dryer MUST exhaust to outside of building, NOT into any concealed space.

•Exhaust installation requires minimum 4"-diameter rigid or semi-rigid metal duct with approved, unobstructed vent hood having swing-out damper(s). If installing rigid metal duct (preferred), do not exceed MAXIMUM venting run length of 64 ft., allow deductions for elbows and vents. If installing semi-rigid metal duct, do not exceed MAXIMUM venting run length of 8 ft., always allow deductions for elbows and vents (Refer to Product Installation Guide on web for additional information). Do NOT use flexible plastic or metal foil duct and use shortest run possible.

•Gas supply line should be 1/2" pipe and MUST have individual shutoff valve.

•Leveling legs supplied to level dryer properly and reduce excessive noise and vibration.

•Water inlet hose for steam setting connects to cold water supply with “Y” connector and requires 3/4" clearance between back of unit and wall.

Note: For planning purposes only. Refer to Product Installation Guide on the web at frigidaire.com for detailed instructions.

Optional Accessories

•Dryer Stacking Kit – (PN # STACKIT4X).

•15" Classic Red Drawer Pedestal – (PN # CFPWD15R).

•15" Classic Blue Drawer Pedestal – (PN # CFPWD15N).

•15" Classic Silver Drawer Pedestal – (PN # CFPWD15A).

•15" Classic White Drawer Pedestal – (PN # CFPWD15W).

•Mobile Home Installation Kit – (PN # 137067200).

•LP Gas Conversion Kit – (PN # PCK4200).

• Drying Rack – (PN # 137067300).

	USA • 10200 David Taylor Drive • Charlotte, NC 28262 • 1-800-FRIGIDAIRE • frigidaire.com	Specifications
	CANADA • 5855 Terry Fox Way • Mississauga, ON L5V 3E4 • 1-800-265-8352 • frigidaire.ca	Specifications
		subject to change.

FASG7073L 09/11

Printed in the U.S.A.