Kenmore 134313400, 417.74182300, 134316200 manual Electrical Connections For 3-WIRE System

Page 2

GREEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

GROUND

 

 

 

 

 

 

 

 

 

 

SCREW

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

SILVER TERMINAL

GREEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NEUTRAL

 

 

 

 

 

 

 

 

 

GROUND

 

 

 

 

 

 

 

WIRE

 

 

 

 

 

 

 

NUT

TIGHTEN NUT

TO THESE

THREADS

STRAIN

RELIEF

MOUNTING

BRACKET POWER CORD

ELECTRICAL CONNECTIONS

FOR 3-WIRE SYSTEM

ELECTRIC Dryer

1.

Remove the screws securing the terminal block access

 

cover and the strain relief mounting bracket located on the

 

back of the dryer upper corner.

2.

Install a U.L. listed strain relief into the power cord entry

 

hole of the mounting bracket. Finger tighten the nut only at

 

this time.

 

 

GREEN POWER

CORD

 

 

GREEN

 

 

GROUND WIRE

 

SILVER TERMINAL

 

 

 

GROUND

 

 

 

 

SCREW

TERMINAL BLOCK

 

GREEN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TIGHTEN

 

 

 

 

 

 

 

 

BLACK

NEUTRAL

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NUT

GROUND

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

TO THESE

 

 

 

 

WHITE

 

 

 

WIRE

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

THREADS

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NUT

 

 

 

RED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

STRAIN

 

 

 

 

 

 

 

 

 

 

RELIEF

 

 

 

 

 

 

 

 

 

MOUNTING

 

 

 

 

 

 

 

 

BRACKET

 

 

 

 

 

 

 

 

 

 

 

 

 

 

POWER

 

 

 

 

 

 

 

CORD

 

 

ELECTRICAL CONNECTIONS

FOR 4-WIRE SYSTEM

ELECTRIC Dryer

1.Remove the screws securing the terminal block access cover and the strain relief mounting bracket located on the back of the dryer upper corner.

2.Install a U.L. listed strain relief in the entry hole of the mounting bracket. Finger tighten the nut only at this time.

3.Remove the green neutral ground wire from the green ground screw located above the terminal block.

 

 

 

 

 

TYPICAL 4

 

BLACK

240V

CONDUCTOR

 

 

 

 

 

 

 

 

RECEPTACLE

 

 

 

 

 

WH

ITE NEUTRAL

 

 

 

 

 

3. Thread a U.L. listed 30 amp. power cord, NEMA 10-30

TYPICAL 4 CONDUCTOR CORD

RED 240V

 

Type SRDT, through the strain relief.

4.

Attach the power cord neutral (center wire) conductor to

 

the silver colored center terminal on the terminal block.

 

Tighten the screw securely.

5.

Attach the remaining two power cord outer conductors to

 

the outer brass colored terminals on the terminal block.

 

Tighten both screws securely.

Do not make a sharp bend or crimp wiring/ conductor at connections.

6.Reattach the strain relief mounting bracket to the back of the dryer with two screws. Tighten screws securely.

7.Tighten the screws securing the cord restraint firmly against the power cord.

8.Tighten the strain relief nut securely so that the strain relief does not turn.

9.Reinstall the terminal block cover.

GREEN GROUND

30 AMP NEMA 14-30 TYPE SRDT OR ST

4.Thread a U.L. listed 30 amp power cord, NEMA 14-30 type ST or SRDT through the strain relief.

5.Attach the green power cord ground wire to the cabinet with the green ground screw.

6.Attach the white (neutral) power cord conductor from the power cord and the green ground wire from the dryer harness (removed from the ground screw in step 3) to the silver-colored center terminal on the terminal block. Tighten the screw securely.

7.Attach the red and black power cord conductors to the outer brass-colored terminals on the terminal block.

Do not make a sharp bend or crimp wiring/ conductor at the connections.

8.Tighten the screws securing the cord restraint firmly against the power cord.

9.Tighten the strain relief nut securely so the strain relief does not turn.

10.Reinstall the terminal block access cover.

7

Image 2
Contents Installation Replacement PartsElectrical Connections For 3-WIRE System Electrical Connections For 4-WIRE SystemElectrical Installation Grounding RequirementsUnpacking Reversing Door SwingDo not Install Your Dryer Location of Your DryerMaximum Length Exhaust System Requirements PRE-INSTALLATION RequirementsElectrical Requirements Installation Instructions Page Repair Parts List CABINET/DRUM Functional Parts 10/03 Non-Illustrated Parts Front PANEL/LINT Filter 131872000 Pin,retainer ,lint blade CONTROLS/TOP Panel Mounting Hardware,meter case ,security P16M0027 Screw,hex head ,1/4-20T x 1.25 ,spacer mtg.,thread cutting Burner 131168200 Screw,pan head ,8-18B x 131243700 Wiring Diagram