Beko DV 7220 X manual Installation, Under counter installation, Mounting over a washing machine

Page 5
Install the product in an environment which has no risk of freezing and is in a stable and level position.
Operate your product in a well ventilated, dust-free environment.
Do not block the air ducts in front of and under the product with materials such as long pile rugs and wooden planks.
Do not place your product on a long pile rug or on similar surfaces.
Do not install the product behind a door with a lock, sliding door or a hinged door which can strike the product.
Once the product is installed, it should stay at the same place where its connections have been made. When installing the product, make sure that the rear wall of it does not touch anywhere (tap, socket, etc.) and also pay attention to install the product at a place where it will stay permanently.

2Installation

It is the customers responsibility to arrange a suitably qualified installer to correctly install this product.

CPreparation of location and electrical installation for the product is under customer’s responsibility.

BInstallation and electrical connections must be carried out by a qualified personnel.

APrior to installation, visually check if the product has any defects on it. If so, do not have it installed. Damaged products will cause risks for your safety.

Appropriate installation location

BDo not place the product on top of the power cable.

Keep at least 1.5 cm distance to walls of other furniture.

Under counter installation

A special part (Part no: 295 970 0100) replacing the top trim must be provided and installed by the suitably qualified installer in order to use the machine under a counter or in a cupboard. It should never be operated without the top trim.

Leave at least 3 cm of space between the side and rear walls of the product and the walls of the counter/cupboard when installing your product under a counter or in a cupboard.

Mounting over a washing machine

A fitting device should be used between the two machines when installing above a washing machine. The bracket (Part no.

296 280 0100 white/296 280 0200 grey) must be installed by the Authorised Service Agent.

Place the product on a firm floor. If it will be

placed on top of a washing machine, the approximate weight of both machines may reach 180 kg when they are full. Therefore, the floor must be capable of carrying the load on it!

Ventilation hose and connection (for products equipped with an outlet vent)

Ventilation hose allows exhaust air from inside the machine

Vented dryer has 1 air outlet.

Stainless sheet metal or aluminum pipes can be used instead of a hose. The pipe diameter should be minimum 10 cm.

Maximum hose and pipe lengths are given in the table below.

 

Hose

Pipe

 

 

 

Maximum length

4 m

5 m

1 elbow 45°

-1.0 m

-0.3 m

1 elbow 90°

-1.8 m

-0.6 m

1 elbow 90° short

 

-2.7 m

1 wall passage

-2.0 m

-2.0 m

CEach elbow and other passages should be subtracted from the maximum length stated above.

To connect a ventilation hose;

1.Connect the air outlet hose to the hose spacer piece by turning it counterclockwise.

2.Make the hose passages as shown below.

CExhaust of humid air from the dryer into the room is inconvenient. It may damage the walls and furniture in the room.

CThe ventilation hose can be routed outdoors via a window or it can be connected to the air outlet in the bathroom.

CAir outlet hose must be routed directly to the outdoors. There must be a limited number of elbows as not to hinder ventilation.

CTo prevent water accumulation in the hose, make sure that it is not folded on the floor.

5 EN

Image 5
Contents Dryer DV 7220 Read this manual prior to initial operation of the product Explanation of symbolsNever operate your dryer without the lint filter installed Important safety informationAlways clean the lint filter before or after each loading Do not allow children sit/climb on or enter in the product Children’s safetyIntended use Under counter installation InstallationAppropriate installation location Mounting over a washing machineElectrical connection Adjusting feetFirst use Disposing of packaging materialTechnical Specifications Things to be done for energy saving Initial preparations for dryingLaundry suitable for drying in the machine Laundry unsuitable for drying in the machinePreparing laundry for drying Following weights are given as examplesCorrect load capacity LoadingControl panel Selecting a Programme and OperatingYour MachineProgramme selection Timer programsMain programmes CottonsProgram selection and consumption table Auxiliary function Time delayStarting the programme Progress of programEnd of programme Finishing by canceling the programmeChild-proof lock Sensor models equipped with a sensor Maintenance and cleaningFilter Cartridge / Door Inner Surface Solution suggestions for problems