Beko DV 7220 X Adjusting feet, Electrical connection, First use, Disposing of packaging material

Page 6
Do not make connections via extension cables or multi-plugs.
The main fuse and switches must have a contact distance of minimum 3 mm.

BThe ventilation hose should not be connected to the chimney of a stove or a fireplace.

BDo not operate your product at the same time with heaters such as a coal or gas stove. Airflow may cause the chimney to flare up.

Adjusting feet

In order to ensure that your product operates more silently and vibration-free, it must stand level and balanced on its feet. Front feet of your product can be adjusted. Balance the machine by adjusting the feet.

1. Loosen the feet by hand.

2. Adjust the feet until the product stands level and firmly on the floor.

CDo not use any tools to loosen the adjustable feet, otherwise, they can be damaged.

CNever remove the adjustable feet from their housings.

2 plastic pieces supplied along with the user manual prevent your machine from slipping on wet and slippery surfaces. To install the plastic parts:

1.Tilt your product to backwards.

2.Fit the plastic parts on to the front adjustable feet. Press on the plastic parts to snap them into their seating.

3.Check the balance of your product

again and readjust the adjustable feet if necessary.

Electrical connection

Connect the machine to a grounded outlet protected by a fuse of suitable capacity as stated in the technical specifications table. Our company shall not be liable for any damages that will arise when the machine is used on a circuit without grounding.

Connection must comply with national regulations.

If the current value of the fuse or breaker in the house is less than 10 Amps, have a qualified electrician install a 10 Amp fuse.

Power cable plug must be within easy reach after installation.

The voltage and allowed fuse or breaker protection are specified in the “Technical Specifications” section.

The specified voltage must be equal to your mains voltage.

BDamaged power cable must only be replaced by a qualified electrician.

BIf the product is faulty, it must not be operated unless it is repaired! There is the risk of electric shock!

First use

To have the product ready for operation before calling the suitably qualified installer, make sure that its location and power supply installations are appropriate. If they are not, call a qualified electrician to have any necessary arrangements carried out.

Make sure that the power connections of the product are in accordance with the instructions given in relevant chapters of this manual.

Disposing of packaging material

Packaging materials are dangerous to children. Keep packaging materials in a safe

place out of reach of children. Packaging materials of your product are manufactured from recyclable materials. Sort and dispose of them in accordance with recycled waste instructions. Do not dispose of them with normal domestic waste.

Transportation of the machine

1.Unplug the machine from the mains.

2.Remove the water drain (if any) and chimney connections.

3.Drain water remaining in the machine completely before transportation.

Disposing of the old machine

Dispose of your old machine in an environmentally friendly manner.

Refer to your local dealer or solid waste collection centre in your area to learn how to dispose of your machine.

Before disposing of your old machine, cut off the power cable plug and make the loading door lock unusable to avoid dangerous conditions to children.

6 EN

Image 6
Contents Dryer DV 7220 Explanation of symbols Read this manual prior to initial operation of the productImportant safety information Always clean the lint filter before or after each loadingNever operate your dryer without the lint filter installed Children’s safety Intended useDo not allow children sit/climb on or enter in the product Appropriate installation location InstallationUnder counter installation Mounting over a washing machineFirst use Adjusting feetElectrical connection Disposing of packaging materialTechnical Specifications Laundry suitable for drying in the machine Initial preparations for dryingThings to be done for energy saving Laundry unsuitable for drying in the machineCorrect load capacity Following weights are given as examplesPreparing laundry for drying LoadingSelecting a Programme and OperatingYour Machine Control panelMain programmes Timer programsProgramme selection CottonsProgram selection and consumption table Starting the programme Time delayAuxiliary function Progress of programFinishing by canceling the programme Child-proof lockEnd of programme Maintenance and cleaning Filter Cartridge / Door Inner SurfaceSensor models equipped with a sensor Solution suggestions for problems