ADC ML-122 Belt Adjustment Motor to Drive Axle, Motorized Impellor Blower Replacement, Motors

Page 17

Refer to basket assembly section page 15 for shaft and basket alignment.

V-Belt Adjustment (Motor to Drive Axle)

Discontinue electrical power to the dryer.

Remove the belt guard cover from the rear of the dryer.

Loosen the 4 bolts holding the drive motor mount to the side of the dryer.

Loosen the jam nuts on the adjustment screw on the top of the motor mount.

Turn the adjustment screw to lower the motor mount (to tighten the belts) or raise the motor mount (to loosen the belts.)

Check the vertical plane of the motor and idler pulleys for parallel adjustment.

If realignment is required, loosen motor pulley and bushing, and move motor pulley to proper position.

Retighten motor mount bolts and jam nuts.

 

Motorized Impellor (Blower) Replacement

 

Reestablish electrical power to the dryer.

 

 

 

Discontinue electrical power to the dryer.

 

 

 

 

Drive Motor V-Belts Replacement

 

Remove lint draw.

 

Discontinue electrical power to the dryer.

 

Remove the perforated panel inside the tumbler.

 

Remove the belt guard cover from the rear of the dryer.

Remove the bolts securing the inlet cone.

 

Loosen tension on V-belt so that it can easily be rolled off

Remove the inlet cone.

 

pulley. This can be done by loosening the 4 bolts holding

Remove the bolts securing the motor plate to the dryer

the motor to the side of the dryer, as well as the adjustment

cabinet.

 

bolt on top.

 

 

 

Remove the motorized impellor along with the motor plate.

Replace V-belt.

 

 

 

 

Retighten V-belt and adjust tension and alignment per

 

 

previous instructions.

 

 

 

Motors

 

 

 

Drive Motor Replacement

 

 

 

Discontinue electrical power to the dryer.

 

 

 

Remove the belt guard cover from the rear of the dryer.

 

 

Remove drive belt.

 

 

 

Disconnect wiring harness from motor.

 

 

 

Remove bolts holding motor to mount and replace with

 

 

new motor. Do not tighten bolts.

 

 

 

Remove pulley from old motor and install on new motor.

 

 

By removing the setscrew from the drive motor pulley.

 

 

NOTE: A gear puller may be required to remove pulley.

 

 

Align motor pulley with drive assembly pulley and tighten

 

 

setscrew holding motor pulley.

 

NOTE: The motorized impellor assembly will not be

 

Replace belts and adjust belt tension.

 

 

 

able to be removed due to the wiring harness still

 

Retighten bolts.

 

connected.

 

Reestablish electrical power to the dryer.

 

Disconnect the wiring harness from motor.

 

 

 

Remove the motor plate from the motorized impellor and

 

 

install it on the new motor.

 

 

 

Reconnect the wiring harness to the motor.

 

 

 

To replace new motorized impellor assembly, reverse steps.

 

 

Reestablish electrical power to the dryer.

 

450412 - 4

www.amdry.com

17

Image 17
Contents ML-96 / ML-122 Serial Numbers Model noTable of Contents Safety Precautions Routine MaintenanceCleaning Important InformationInstallation Requirements Description of Parts Operational Service Check ProcedureElectrical and Gas Requirements Control Panel MicroprocessorReversing Relay Panel Gas Burner AssemblySteam Coil and Damper System Steam Coil pH LevelIdler Shaft Assembly Drive Shaft AssemblyMain Door Switch Sail Switch Gas Models OnlyServicing Gas Valve Replacement Microprocessor Temperature Sensor Probe ReplacementBrushing on a soapy water solution Main Burner Orifices ReplacementIgnition Module Replacement Burner Tubes ReplacementThermostats To Convert Natural Gas to L.P. GasSteam Damper Actuator System Service and Replacement Sail Switch Assembly Gas Models OnlyMay be needed to remove and install the steam coil Steam Coil ReplacementMain Door Switch Replacement Front Panel and Main Door AssembliesFront Panel Replacement Drive Motor Pulley ReplacementBasket Assembly Adjustment Tumbler Wheel Replacement on Drive AssemblyTumbler Wheel Replacement on Idler Assembly Inch Support Wheel Replacement 15/16 5 cm Flange Bearing ReplacementRotational Sensor Assembly Idler Shaft Pillow Block Bearing ReplacementMotorized Impellor Blower Replacement Belt Adjustment Motor to Drive AxleDrive Motor V-Belts Replacement Drive Motor ReplacementTroubleshooting Burner hi-limit safety thermostat Is tripping Phase 6 OPL System DiagnosticsDiagnostic L.E.D. Display Failure Codes Overload for impellor fan motor Is trippingD. Display Indicator Number D. Display IndicatorsAIR AIR JET Output L.E.D. Indicator Optional FAN Blower Output L.E.D. IndicatorHT1 Heat Output L.E.D. Indicator Fuse Main Fuse Input L.E.D. IndicatorDiagnostic L.E.D. Display Fault Messages Phase 7 OPL System DiagnosticsData Label Input/Output Board L.E.D. IndicatorsInputs OutputsHow to Use a Manometer 450412 ADC Part No 4 01/02/08
Related manuals
Manual 59 pages 3.4 Kb

ML-96, ML-122 specifications

The ADC ML-122 and ML-96 are two advanced communication devices designed for efficient data collection and transmission in various applications. Both models are renowned for their robust performance and user-friendly features, which cater to a diverse range of industries.

The ADC ML-122 is a high-performance data logger that excels in multi-channel monitoring. It supports various input types, making it versatile for applications such as environmental monitoring, industrial process control, and research. One of its standout features is its ability to accommodate both analog and digital signals, allowing users to gather a wealth of data from different sources. The device supports a wide temperature range, ensuring reliability in diverse environmental conditions. Moreover, its built-in memory can store extensive data logs, which are easily downloadable for analysis.

On the other hand, the ADC ML-96 is designed primarily for telecommunication and network monitoring. It features advanced signal processing technologies that allow it to analyze and troubleshoot communication lines efficiently. The device is equipped with real-time monitoring capabilities, enabling users to detect issues as they arise, which is crucial in maintaining network integrity. The ML-96's compact design makes it an ideal choice for installation in tight spaces without sacrificing performance.

Both models are built with cutting-edge technologies that enhance their functionality. They integrate wireless communication protocols, such as Wi-Fi and Bluetooth, enabling seamless connectivity to cloud services for data backup and remote access. This feature empowers users to monitor conditions from anywhere, ensuring that critical information is always at hand.

The user interface for both the ML-122 and ML-96 is designed for ease of use. Equipped with a clear display and intuitive controls, users can navigate through settings and view data with minimal training. The devices also offer customizable alerts that notify users of any anomalies, adding an additional layer of security and responsiveness.

In terms of power management, both models utilize energy-efficient components, allowing for extended battery life. This is particularly advantageous in remote sensing applications where power sources may be limited. Furthermore, the ability to integrate with other systems makes these models adaptable to various operational needs.

In conclusion, the ADC ML-122 and ML-96 stand out in their respective markets due to their innovative features, reliable technologies, and user-friendly designs. With their flexibility and performance, they continue to set the standard for data logging and communication monitoring technologies.