American Dryer Corp D3030 installation manual

Page 33

a.The pressure of the condensate in the steam supply line will cause water hammer and subsequent heat exchanger (steam coil) failure. The steam supply connection into the main supply line must be made with a minimum 10-inch (25.4 cm) riser. This will prevent any condensate from draining towards the dryer.

b.The steam supply line to the dryer must include a 12-inch (30.48 cm) riser along with a drip trap and check valve. This will prevent any condensate from entering the steam coil.

c.Flexible hoses or couplings must be used. The dryer vibrates slightly when it runs and this will cause the steam coil connections to crack if they are hard piped to the supply and return mains.

d.Shutoff valves for each dryer should be installed in the supply line, return line, and drip trap return line. This will allow the dryer to be isolated from the supply main and the return main if the dryer needs maintenance work.

e.Install an inverted bucket steam trap and check valve at least 12-inches (30.48 cm) below the steam coil as close to the coil as possible.

1)A trap with a capacity of 350 lbs (160 kg) of condensate per hour at 125 psi (8.61 bar) is needed for each unit.

f.The supply line and the return line should be insulated. This will save energy and provide for the safety of the operator and maintenance personnel.

g.Water pockets in the supply line, caused by low points, will provide wet steam to the coil possibly causing steam coil damage. ALL horizontal runs of steam supply piping should be pitched 1/4-inch (6.35 mm) for every 1 foot (0.30 meters) back towards the steam supply header causing the condensate in the line to drain to the header. Install a bypass trap in any low point to eliminate wet steam.

IMPORTANT: Flexible hoses/couplings must be used. Coil failure due to hard plumbing connections will VOID THE WARRANTY.

29

Image 33
Contents D30 Retain This Manual In a Safe Place For Future Reference For Your Safety Page Table of Contents Section Procedure for Functional Check Receiving and Handling Important InformationWhat to do if YOU Smell GAS Safety PrecautionsStandards Specifications SpecificationsSpecifications GAS, ELECTRIC, or Steam UNPACKING/SETTING UP Installation ProceduresLocation Requirements Dryer Enclosure Requirements Fresh AIR Supply Requirements Exhaust Requirements Single Dryer Venting Vertical Venting Multiple Dryer Common Venting Illus. C Important Venting Reminders Electrical Requirements Electrical InformationGAS and Steam KW Electric Page Single-Phase Electrical Lead Connections Page GAS Information Type of GAS Page Page Steam Information Operating Steam PressurePage Compressed AIR Supply AIR Pressure Page Page Preparation for OPERATION/START-UP GAS Models only Preoperational TestsBasket Tumbler Coating Preoperational InstructionsPage NON-COIN Models Shutdown Instructions SERVICE/PARTS Information ServiceParts Warranty Information Returning Warranty CardsWarranty Routine Maintenance CleaningSuggested Cleaning Schedule Lubrication AdjustmentsLint Drawer Removal Data Label Information Serial Number Timing Legend Reversing Timer SPIN/DWELLADJUSTMENTSProcedure for Functional Check Replacement Components Page Sensor Activated Fire Extinguishing S.A.F.E. System F.E. System In ActionBefore YOU Start Check Local Codes and Permits InstallationTypical water supply Optional Manual Bypass System Reset F.E. System Solenoid Water Valve 24V 50/60 Hz 822752

D3030 specifications

American Dryer Corp D3030 is a state-of-the-art commercial dryer designed to meet the needs of high-demand laundry environments. Renowned for its efficiency, durability, and advanced technology, the D3030 has become a preferred choice among laundromats, hotels, and other facilities requiring reliable laundry solutions.

One of the standout features of the D3030 is its powerful drying performance. Equipped with a robust 30-pound capacity, it can effectively handle large loads, significantly reducing drying times and increasing productivity. The dryer utilizes a high-efficiency heat source that not only quickens the drying process but also conserves energy, making it an environmentally friendly option. The dual airflow system enhances drying efficiency by ensuring even heat distribution throughout the drum, resulting in thoroughly dried laundry every time.

The D3030 incorporates advanced technology for optimal control and user convenience. A digital control panel allows operators to easily select drying cycles, temperatures, and times, tailoring the process to the specific needs of various fabrics. The intelligent sensor system monitors moisture levels within the drum, adjusting the drying time accordingly. This feature not only prevents over-drying and fabric damage but also saves energy, making the dryer more cost-effective to operate.

Durability is another hallmark of the D3030. Constructed with heavy-duty materials, it is designed to withstand the rigors of daily use in high-traffic environments. The stainless-steel drum is both rust-resistant and easy to clean, ensuring a long operational lifespan. Its sturdy design minimizes vibration and noise, contributing to a quieter working environment.

Safety features are paramount in the D3030’s design. It includes a thermal fuse and other safety mechanisms to prevent overheating, giving operators peace of mind while using the dryer. Additionally, a large door with a secure latch allows for easy loading and unloading, enhancing user experience.

In summary, the American Dryer Corp D3030 is a powerful, efficient, and durable commercial dryer that excels in meeting the demands of any busy laundry operation. With its combination of advanced technology, customizable settings, and safety features, it offers a comprehensive solution for those seeking high-performance drying capabilities. The D3030 stands as a testament to American Dryer Corp's commitment to quality and innovation in the laundry industry.