Whirlpool 8LSC6244BG0 Operating Your Washer, Before starting your washer, Selecting a load size

Page 5

Operating Your Washer

In This Section

Page Before starting your washer .............................. 6

Starting or stopping your washer ..................... 6 Selecting a load size .......................................... 5 Selecting wash-rinse temperatures .................. 6

 

 

 

 

 

Page

Selecting a cycle and

time

...... 6

Using

rinse

and

spin

..................__

6

Using

drain

and

spin

.................................

...... 9

What

happens

in each

cycle

...... 9

Operating your washer properly ensures maximum washing efficiency. This section gives you important information to help you to select a cycle, time, and temperature for your wash load.

Before starting your washer

Add measured detergent. Then place a sorted load in the washer before starting. See page 12 for additional “Beforeyou wash” information.

NOTE: If your washer has a Consumer Buy Guide, remove it and place it in your Use and Care Guide.

Starting or stopping your washer

Starting your washer:

1.Select a load size and water temperature.

2.Push in the Cycle Control Knob and turn it clockwise. Stop when the indicator on the knob’s outer ring points to the number in the wash cycle you want. The numbers are minutes of wash time.

3.Pull out the Cycle Control Knob.

Refer to pages 6-9 for additional information to help you make selections.

Stopping and restarting your washer:

l

l

To stop the washer at any time, push in the

Cycles may vary with model

Cycle Control Knob.

 

To restart the washer, close the lid (if neces-

 

sary) and pull out the Cycle Control Knob.

 

Selecting a load size

Your washer has a knob or slide Load Size Selector. Position the Load Size Selector at the setting that corresponds to the size load you want to wash.

Select a load size based upon the size of the load and the fabric you are washing. See page 12 for additional loading information.

lIf your washer has a knob Load Size Selec- tor, turn selector to the desired load size.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents UseAndCare Thank you for buying a Whirlpool appliance Your safety is important to usHelp when you need it Please Important SAFt InstructionsUnderstanding your responsibilities +Available on some models Knowing Your Washer’s FeaturesBefore starting your washer Operating Your WasherStarting or stopping your washer Selecting a load sizeSelecting wash-rinse temp Water temperature tipsLoad size tips Rinse waterDelicate cycle Regular cyclePermanent Press cycle Short cycle Using rinse and spinSoak/Pre-Wash cycle Super Wash cycleWhat happens in each cycle LJ4t SpinWash selected time Drain or partial drain+ No agitation Fill Rinse Drain-No agitation IllJ% Spin-Spray rinseUsing the extra rinse option Other FeaturesUsing the fabric softener DispenserUndiluted bleach will damage any fabric it touches Using the chlorine bleach dispenserMagic CLEAN* lint filter Before you wash Laundry TipsLoading suggestions Removing stainsPrewashing or soaking Stain removal rulesStain removal guide Solvent. Wash Egg -~Hardness Water TemperatureUsage Guide Chlorine bleach Using laundry aidsFabric softeners All-fabric bleachWash following manufacturer’s instructions Washing special-care itemsThey are washed. This is normal Stretch. However Could stick to the next load and cause skin irritationThis means that knits are more likely to be stretched Unless they areProblem Solving laundering problemsCare during periods Caring for your washerNon-use Saving energyWait a minute to see if washer starts cycle again If You Need Assistance Or ServiceBefore calling for assistance Set cycle control knob on correct number in the cycle If you need FSP* replace- ment partsAssembly Materials or workmanship. Service must be provided by anFrom Date of Purchase Authorized Whirlpool Service company
Top Page Image Contents