Haier HWM78-0528T user manual Usage the drain hose, Program select

bSteps of using the operation buttons and description of the steps

How to change the direction of the drain hose

1.Dismantle the rear cover of the washing machine.

3.Dismantle the drain outlet protecting cover at the other side,

PROGRAM STANDARD SOAKHEAVY GENTLE SAVE COTTON SINGLE WASH RINSESPIN SINGLE SPIN TUB CLEAN AIR DRY

INDICATION OF PROCESS (NO CHOOSING) SOAK WASH RINSE SPIN

HT

LIG

	TIME REMAINED(M INUTES)	SH
		FLA
	RESERVE(HOURS LATER)
START
PAUSE	PROGRAM/RESERVE

POWER

ON/OFF

WATER

LEVEL Digital display

Fuzzy logic control

10 water level selection

2.Put down the drain hose .Take off the drain hose frame as indicated in Figure 1.Take the drain hose into the cabinet ,then nip the drain fixing clamp to make it deviated from the clip,the other hand is used to put down the drain bushing,as indicated in Figure 2,3.

	Drain hose
Figure 1	Drain hose support		Drain bushing
			Figure 2
	Cabinet
	Inner	Outer
	Push		Drain bushing

(the way is the same as the drain bushing),then install the drain bushing, as indicated in Figure 4.

4.Extend the drain hose from the other side. Fix the drain hose with drain hose frame onto the cabinet, as indicated in Figure 5.

Drain outlet protecting cover

Figure 4 Figure 5

Drain bushing

5.Install the drain outlet protecting cover to the other side, as indicated in Figure 6

1.Push "POWER"button to switch on the power

POWER

ON/OFF

Drain hose fixing	Take down
clamp
Push	Figure 3

Figure 6

2.Push "PROGRAM/RESERVE" button to select
suitable automatic program	PROGRAM/RESERVE

Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose with our company serviceman .

Usage the drain hose

After the power is switched on, "standard" is automatically set. To select other full-auto program, please push the "PROGRAM/RESERVE" button till the corresponding indicator is on. Refer to the "PROGRAM/RESERVE button" on Page 11.E.g

For instance:select "SAVE" program for small quantity of laundries with light soil.

Program select

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way.

2.Do not step on or press the drain hose.

4.If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m.

The display of digitron	Program	Application				The running process
				(the digitron displays the running process)
01	STANDARD	Common washing		WASH(	)	RINSE(	)	SPIN(	)
02	SOAK HEAVY	Washing for coverlet	bigger laundries	SOAK(	)	WASH(	)	RINSE(	) SPIN( )
03	GENTLE	Washing the woollen	silk textiles	WASH(	)	RINSE(	)	SPIN(	)
04	SAVE	Washing for normal laundries		WASH(	)	RINSE(	)	SPIN(	)
05	COTTON	Washing the cotton textiles		WASH(	)	RINSE(	)	SPIN(	)
06	SINGLE WASH	Reusing the washing detergent		WASH(	)
07	RINSE SPIN	Washing the cloth washed by hand		RINSE(	)	SPIN(	)
		(first draining, then spinning)
08	SINGLE SPIN	Only spinning the cloth wet or washed by		SPIN(	)
		hand (first draining, then spinning)
09	TUB CLEAN	The spinning time is the same to the single spin,		SPIN(	)
		but spinning in lower
10	AIR DRY	Avoid growing mildew on the outer tub and the		SPIN(	)
		inner tub

3. If the drain hose is too long, cut it at mid point. To make		5.If the extra hose is too long, cut it either at A or at B.
	smooth drainage, cut the front end of the hose slantingly.

12 5