Install the water inlet hose
Confirm the water faucet
Water faucet,suitable | Water faucet,not suitable |
Outlet end surface |
|
>10mm |
|
It is required that the front end shall be longer than 10mm.
The exit end face of the faucet shall be flat and smooth. If not please file it to avoid leakage.
Reserve, remain time digitron | "Power" button | ||||||
It displays | Push the "power" button to switch on the power. | ||||||
It displays remained reserve time (hour). | Under | ||||||
It displays total remained time (min). | Push the "power" button to switch on the power. If | ||||||
It displays abnormal symbol in abnormal situation. | the "start/pause" button is not pushed, the machine | ||||||
(See to Page15) | will switch off the power automatically after 5 minutes. | ||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Connection between the water inlet hose jointer and the water faucet
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the water inlet hose component. See to Figure 1.
2.Loosen the screw till the water faucet can be accessed. Put the jointer of the water inlet hose on the faucet. See to Figure 2. (If the faucet is too large and the jointer can not be set on the water faucet, please loosen the four screws and take out the bushing in the jointer. The front end of the faucet must be smooth, otherwise it may leak water. See to Figure 3.)
water inlet hose jointer |
|
|
Slider |
| Screw |
|
| |
Screw knife |
| Sign plate |
| Bushing | |
Lock level |
|
|
water inlet hose |
|
|
Figure 1 | Figure 2 | Figure 3 |
Reserve
43
46
36
40
28
32
20
2 4
12
16
Water level
Standard 
Normal 
Tub dry
Fibre 
Quick
Woollen
Jean
Power
dry
Tub
Program
TUB DRY button
Push the"TUB DRY"button,the indicator is lighted,and the"TUB DRY"function is operating. After washing,the innerand outer tub is wet,mildew may grow not using for a long time.Then,the
"TUB DRY" fuction can make the tub dry preventing mildew from
growing.
Notice: When "Tub Dry" have been selected, all functions are unavailable except " Reserve" , the indicators of Spin, Tub Dry and Reserve LED are lighted, and others are off.
3.Fasten the four screws evenly. See to Figure 4.
4 Take off the nameplate. Twist the fastening nut as per the indication of the figure to seal up the exit end face of the faucet. See to Figure 5.
remark: Before installation, the threading is 4mmabove the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut. See to figure 6.
About 4mm before twisting
About less than 2mm after twisting
Screw nut
Figure 4 | Figure 5 | Figure 6 |
"Reserve" button
The digitron displays remain time before washing is finished (in minutes)
Push "reserve" button, the digitron displays the reserve time of washing (in hours). The indicator flashes to indicate that the reserve function
is operating.Push "reserve" button to display the reserve mode.
WATER LEVEL 
button
The washing machine can detect the laundries automatically. After detection, it will set the water level to suitable value among 24L,32L,40L,46L automatically.
You can also set water level by yourself. After the machine is started, it
will not set water level automatically. You shall push the start/pause button to make new setting.
If there's water inside the tub, the machine cannot detect the laundries and will display water level 32L .
If wet laundries are put in, it may display water level 46L . You must set suitable water level by yourself.
If QUICK programs selected, it will display water level 20L . When water level 16L is reached in water filling, it will perform washing while filling water. When water level 20L is reached, it will change to normal washing.
If WOOLLEN program selected,water level only can be set between 32L and 46L.
During operation of wash,soak and rinse program, you can push down the water level button to add water. When you release the button, or it reaches the overflow water level, the machine will stop adding water.
The water level decided may be different from actual value because of the different moisture level of the laundries.
PROGRAM selection button
Following automatic programs are available for selection
PROGRAM | Applicable situation |
STANDARD | Common washing |
QUICK | Quick and |
laundries | |
JEAN | Washing the relatively big and thick laundries |
FIBER | Washing the chemical fiber laundries |
WOOLLEN | Washing the woolen textiles |
NORMAL | Common washing |