Haier HWM65-0566 Description of the steps, How to change the direction of the drain hose

Page 7

b Steps of using the operation buttons and

description of the steps

How to change the direction of the drain hose

1.Dismantle the rear cover of the washing machine.

3.Dismantle the drain outlet protecting cover at the other side, (the way is the same as the drain bushing),then install the drain

Soak

20

15

43

36

28

20

12

46

 

Standard

 

Normal

Tub dry

 

 

 

 

 

 

4 0

 

Fibre

 

Quick

 

 

 

 

 

 

 

3 2

 

Woollen

 

Jean

 

2 4

1 6

er Pow

dry

Tub

2.Put down the drain hose Take off the drain hose frame as indicated in Figure 1.Take the drain hose into the cabinet then nip the drain fixing clamp to make

it deviated from the clip

the other hand is used to put

down the drain bushing

as indicated in Figure 2 3.

bushing, as indicated in Figure 4.

4.Extend the drain hose from the other side. Fix the drain hose with drain hose frame onto the cabinet, as indicated in Figure 5.

Wash

6

Rinse

Spin Reserve

Program

Water

level

Drain hose

drain outlet protecting

cover

5

Drain hose support

 

Drain bushing

Figure 1

Cabinet

Figure 2

Inner

Outer

 

 

 

Push

 

Drain bushing

Figure 4

Figure 5

Drain bushing

 

5.Install the drain outlet protecting cover to the other side, as indicated in Figure 6

1.Push "power" button to switch on the power

Power

2.Push "program" button to select suitable full-auto program

After the power is switched on, "normal"is automatically set. To select other full-auto program, please push the "program" button till the corresponding indicator is on. Refer to the "Program button" on Page 11.

Drain hose fixing

Take down

clamp

Figure 6

Push

Figure 3

Remarks: in order to make sure of the correct of installation, it is suggested to change the direction of the drain hose with our company serviceman .

Usage the drain hose

E.g. Set to "Quick wash" program for small quantity of laundries with light soil.

In selecting the NORMAL or standard program, the machine will execute fuzzy program to select water and wash time according to the cloth and weight of the laundries. The full procedure is controlled automatically.

Push the "SOAK", "WASH", "RINSE" OR "SPIN" button to select suitable procedure.

The drainage shall be smooth with the drain hose.

1.The height of the drain hose shall be less than 10cm, or the drainage will not be smooth, and cost such long time that the machine may stop at mid way.

2.Do not step on or press the drain hose.

4.If extra drain hose is needed, please make separate purchase. The inner diameter of the extra hose shall not less than 30mm, and the length shall not exceed 1.5m.

Soak

Wash

Rinse

Spin

 

 

 

3. If the drain hose is too long, cut it at mid point. To make 5.If the extra hose is too long, cut it either at A or at B. smooth drainage, cut the front end of the hose slantingly.

12

5

Image 7
Contents Fully Automatic Washing Machine Contents Names of the parts Meaning and description of the symbols SpecificationExplanation Safety precautionsCommon phenomena PhenomenaDisposal after washing Safety precautions Confirm the operation of reserve program Installation and adjustmentInstall the bottom plate Close the top lid Finish washingDescription of the steps How to change the direction of the drain hoseUsage the drain hose Confirm the water faucet Install the water inlet hoseProgram selection button Connection between the water inlet hose and the washer Use the operation buttonsDismantle the water inlet hose Preparation before washing How to use softenerHow to use washing powder How to use whitener