Humminbird 700 manual System Status, GPS Diagnostic View, Self Test, Accessory Test

Page 24

www..reelschel531427-1 C - 767_Man_mEng.aticqxd 10/25/2005..com10:29 AM Page 46

A message will appear on the display periodically to remind you that you are using the Simulator.

Exit the Simulator by powering your 700 Series™ Fishing System off.

System Status

Use System Status to view system connections and to conduct a unit self-test.

The following screens are displayed in turn when you press the VIEW button when using System Status:

•Self Test

•Accessory Test

•GPS Diagnostic View.

Exit System Status by powering your Fishing System off.

GPS Diagnostic View

GPS Diagnostic View shows a sky chart and numerical data from the GPS receiver. The sky chart shows the location of each visible GPS satellite with its satellite number and a signal strength bar. A dark grey bar indicates that the satellite is being used to determine your current position. A light gray bar indicates that the satellite is being monitored, but is not yet being used.

This view also reports the current position, local time and date, and other numeric information. The current GPS Fix Type is reported as No Fix, 2D Fix, 3D Fix, or Enhanced. An Enhanced fix has been augmented using information from WAAS, EGNOS, or MSAS. A 3D or Enhanced Fix is required for navigation. HDOP (the Horizontal Dilution of Precision) is a GPS system parameter which depends on the current satellite configuration. HDOP is used to calculate the Estimated Position Error.

GPS Diagnostic View

Self Test

Self Test displays results from the internal diagnostic self test, including unit serial number, Printed Circuit Board (PCB) serial number, software revision, total hours of operation and the input voltage.

System Status Self Test Screen

Accessory Test

Sky Chart

Satellite Being

Monitored

Current Latitude

and Longitude

Satellite Being Used

Accessory Test lists the accessories connected to the system.

NOTE: The speed accessory will be detected only if the paddlewheel has moved since your 700 Series™ Fishing System was powered up.

System Status Accessory Test Screen

PC Connect

(with PC Connect cable only)

Use PC Connect to update the software of the 700 Series™ Fishing System control head. This feature requires the use of the PC Connect Cable. Complete instructions are included with the PC Connect Cable accessory.

NOTE: The PC Connect Cable requires a separate purchase. For more information visit our website at www.humminbird.com or contact our Customer Resource Center at 1-800-633-1468.

Exit PC Connect mode by powering the 700 Series™ Fishing System off.

37

38

Page 23 Page 25
Image 24
Page 23 Page 25
Contents Atic Table of Contents Thank YouNavigation Menu Tab Views Menu Tab Accessories Menu Tab Peak to Peak measures power output at the highest points How Sonar WorksDualBeam Plus Sonar QuadraBeam SonarWideSide Sonar With optional-purchase QuadraBeamTM transducerSoftware Updates How GPS and Cartography WorkMulti-Media Card MMC/SD Slot 200 KHz WithF f e r e n t Bait Ball Hard Bottom Rocky BottomDistance distance Traveled withAverage Speed Average speed readingZoom View Chart View 200/83 kHz Split Sonar View ViewsSonar View Sonar viewsUnderstanding Sonar History Real Time Sonar RTS WindowFreeze Frame Bottom PresentationSonar Zoom View Sonar Zoom View200/83 kHz Split Sonar View Circular Flasher ViewScreen Snapshot View Big Digits ViewSide Beam View Side Beam ViewBird’s Eye View WideSide ViewBird’s Eye View Chart View Combo ViewView Orientation Viewing Cartography Waypoints, Routes and TracksSave, Edit, or Delete a Waypoint Navigate to a Waypoint or PositionSave, Edit or Delete a Route Save or Clear a Current TrackAdd a Waypoint Target or Trolling Grid Press menuPOWER/LIGHT Key Edit, Delete or Hide Saved TracksKey Functions View KeyAccessory Bus WAY Cursor Control KeyMark Key Goto KeyPowering Up the Unit Menu SystemTitle Screen Start-Up Options Menu Normal OperationSimulator GPS Diagnostic View Accessory TestSystem Status Self TestTo adjust the Side Sonar X-PressTMMenuSide Sonar views onlyTo adjust the Sensitivity To adjust the Upper RangeSensitivity Upper RangeChart Speed Lower RangeSide Beam Range Cancel Navigation Bottom ViewBottom Range Bottom LockNavigation X-PressTMMenu Waypoint NameNavigation views only Only with an active cursor on a waypointCursor to Waypoint Save Current TrackClear Current Track Save Current RouteRemove Target Remove GridSonar Window Screen Snapshot X-Press TM Menu Delete ImageDelete All Images Sonar Menu TabBeam Select Fish ID+TMTo use Beam Select To turn Fish ID+ on or offFish ID Sensitivity Zoom WidthKHz Sensitivity KHz BalanceTo change the 455 kHz Balance setting To change the Depth Lines settingWideSide Sensitivity Depth LinesSurface Clutter Noise FilterMax Depth To change the Water Type setting Water TypeTransducer Select Navigation Menu TabCurrent Track Saved TracksWaypoints Chart Orientation RoutesNorth Reference Grid RotationTrack Min Distance Map DatumCourse Projection Line Export All Nav DataChart Menu Tab Chart Detail LevelTo change the Chart Detail Level setting To change the Map Borders settingLat/Lon Grid Spot SoundingsSet Simulation Position Set Map OffsetAlarms Menu Tab Depth AlarmFish ID Alarm To change the Depth Alarm settingLow Battery Alarm Temp AlarmOff Course Alarm Arrival AlarmDrift Alarm Setup Menu TabAlarm Tone User Mode Units DepthUnits Temp Units DistanceTriplog Reset Restore DefaultsSelect Readouts Advanced, Sonar view onlyDepth Offset Temp OffsetSpeed Calibration Advanced, with Temp/Speed onlyPosition Format Time FormatDate Format Nmea OutputAccessories Menu Tab Using Screen SnapshotViews Menu Tab To Change the View Status of Any ViewTroubleshooting To make a screen snapshot Screen Snapshot must be enabledTo view screen snapshots Display Problems Finding the Cause of NoiseSeries Fishing System Accessories SpecificationsGlossary Sonar Terms100 Receiver See Transmitter 102104 GPS & Navigation Terms Magnetic North 108Contact Humminbird
Top Page Image Contents