Humminbird 700 manual To adjust the Sensitivity, To adjust the Upper Range

Page 26

www..reelschel531427-1 C - 767_Man_mEng.aticqxd 10/25/2005..com10:29 AM Page 50

Sensitivity

Sensitivity controls how much detail is shown on the display and will adjust the sensitivity of all sonar frequencies. Increasing the sensitivity shows more sonar returns from small baitfish and suspended debris in the water; however, the display may become too cluttered. When operating in very clear water or greater depths, increased sensitivity shows weaker returns that may be of interest. Decreasing the sensitivity eliminates the clutter from the display that is sometimes present in murky or muddy water. If Sensitivity is adjusted too low, the display may not show many sonar returns that could be fish.

NOTE: The Sensitivity setting is a global setting and will adjust the sensitivity of all sonar frequencies, as compared to specific sensitivity adjustments (such as 83 kHz Sensitivity, 455 kHz Balance or Wideside Sensitivity) that allow you to adjust the level of sensitivity for one specific beam at a time.

Sensitivity at Low

Sensitivity at Medium

Sensitivity at High

To adjust the Sensitivity:

1.Highlight Sensitivity on the Sonar X-PressTMmenu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Sensitivity setting. (Low = 1, High = 20, Default = 10)

Upper Range

(Advanced: Sonar, Split Sonar, Big Digits and Circular Flasher

views only)

Upper Range sets the shallowest depth range that will be displayed on the Sonar, Split Sonar, Big Digits and Circular Flasher Views. The Upper Range menu choice is available when User Mode is set to Advanced (see Setup Menu Tab: User Mode) and can only be accessed from the Sonar, Split Sonar, Big Digits and Circular Flasher Views. Upper Range is often used with Lower Range.

For example, if you are only interested in the area between 20 and 50 feet deep, you should set the Upper Depth Range to 20 and the Lower Depth Range to 50. The Sonar View will then show the 30 foot area between 20 and 50, and will not show the surface or the bottom (assuming the bottom is deeper than 50 feet), and will show greater detail for that area between 20 and 50 feet.

NOTE: A minimum distance of 10 feet will be maintained between the Upper and Lower Range regardless of the manual settings entered.

To adjust the Upper Range:

1.Make sure you are in Advanced Mode, then highlight Upper Range on the Sonar X-PressTMmenu.

2.Use the LEFT or RIGHT 4-WAY Cursor Control keys to increase or decrease the Upper Range setting. (0 to 1490 feet or 0 to 497 meters [International Models only], Default = 0)

41

42

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Atic Table of Contents Thank YouNavigation Menu Tab Views Menu Tab Accessories Menu Tab Peak to Peak measures power output at the highest points How Sonar WorksWideSide Sonar DualBeam Plus SonarQuadraBeam Sonar With optional-purchase QuadraBeamTM transducerMulti-Media Card MMC/SD Slot Software UpdatesHow GPS and Cartography Work F f e r e n t 200 KHzWith Bait Ball Hard Bottom Rocky BottomAverage Speed Distance distanceTraveled with Average speed readingSonar View Zoom View Chart View 200/83 kHz Split Sonar ViewViews Sonar viewsFreeze Frame Understanding Sonar HistoryReal Time Sonar RTS Window Bottom PresentationSonar Zoom View Sonar Zoom ViewScreen Snapshot View 200/83 kHz Split Sonar ViewCircular Flasher View Big Digits ViewSide Beam View Side Beam ViewBird’s Eye View Bird’s Eye ViewWideSide View View Orientation Chart ViewCombo View Viewing Cartography Waypoints, Routes and TracksSave, Edit, or Delete a Waypoint Navigate to a Waypoint or PositionAdd a Waypoint Target or Trolling Grid Save, Edit or Delete a RouteSave or Clear a Current Track Press menuKey Functions POWER/LIGHT KeyEdit, Delete or Hide Saved Tracks View KeyMark Key Accessory BusWAY Cursor Control Key Goto KeyTitle Screen Powering Up the UnitMenu System Simulator Start-Up Options MenuNormal Operation System Status GPS Diagnostic ViewAccessory Test Self TestSide To adjust the SideSonar X-PressTMMenu Sonar views onlySensitivity To adjust the SensitivityTo adjust the Upper Range Upper RangeSide Beam Range Chart SpeedLower Range Bottom Range Cancel NavigationBottom View Bottom LockNavigation views only Navigation X-PressTMMenuWaypoint Name Only with an active cursor on a waypointClear Current Track Cursor to WaypointSave Current Track Save Current RouteSonar Window Remove TargetRemove Grid Delete All Images Screen Snapshot X-Press TM MenuDelete Image Sonar Menu TabTo use Beam Select Beam SelectFish ID+TM To turn Fish ID+ on or offKHz Sensitivity Fish ID SensitivityZoom Width KHz BalanceWideSide Sensitivity To change the 455 kHz Balance settingTo change the Depth Lines setting Depth LinesMax Depth Surface ClutterNoise Filter Transducer Select To change the Water Type settingWater Type Navigation Menu TabWaypoints Current TrackSaved Tracks North Reference Chart OrientationRoutes Grid RotationCourse Projection Line Track Min DistanceMap Datum Export All Nav DataTo change the Chart Detail Level setting Chart Menu TabChart Detail Level To change the Map Borders settingSet Simulation Position Lat/Lon GridSpot Soundings Set Map OffsetFish ID Alarm Alarms Menu TabDepth Alarm To change the Depth Alarm settingOff Course Alarm Low Battery AlarmTemp Alarm Arrival AlarmAlarm Tone Drift AlarmSetup Menu Tab Units Temp User ModeUnits Depth Units DistanceSelect Readouts Triplog ResetRestore Defaults Advanced, Sonar view onlySpeed Calibration Depth OffsetTemp Offset Advanced, with Temp/Speed onlyDate Format Position FormatTime Format Nmea OutputViews Menu Tab Accessories Menu TabUsing Screen Snapshot To Change the View Status of Any ViewTo view screen snapshots TroubleshootingTo make a screen snapshot Screen Snapshot must be enabled Display Problems Finding the Cause of NoiseSeries Fishing System Accessories SpecificationsGlossary Sonar Terms100 Receiver See Transmitter 102104 GPS & Navigation Terms Magnetic North 108Contact Humminbird
Top Page Image Contents