Humminbird LCR 40.ID manual

Page 9

www..reelschel matic..com

4.Put transducer in the water. The bottom of the transducer should be in a flat area and should be in good contact with the bottom of the boat.

5.Operate the LCR with the boat operating at high speed. The transducer may have to be moved in order to find an area where satisfactory operation is observed.

6.When an area is found that produces satisfactory operation, mark the location of the transducer.

7.Remove the water and transducer and clean the marked area and the bottom of the transducer thoroughly.

8.Using the Humminbird Epoxy Kit or equivalent, mix an ample amount of epoxy without causing it to bubble and pour it in the area the transducer is to be mounted. The puddle should be larger than the bottom of the transducer.

9.Coat the bottom of the transducer with epoxy, then put it in the center of the puddle and push down on the transducer while moving it around in a circular motion. This forces out any air bubbles that may be trapped between the bottom of the transducer and the hull of the boat.

10.Let epoxy cure then the transducer is ready to operate. No water is now required in the bottom of the boat and gas and oil that is spilled inside of the boat will not degrade performance as it will if the transducer is placed only in water.

CAUTION: Do not use the silicone seal or any soft adhesive to bond the transducer to the hull. This will reduce the sensitivity of the unit.

CAUTIONS

1.Occasionally the “eye“ of your transducer may become dirty from storage or from contact with oils present in boats or marina environments. (Oil will cause the “eye” to lose the intimate contact with the water which is necessary for efficient operation.) The “eye” may be cleaned with liquid detergent.

2.Improper installation of the transducer can alter the efficiency and accuracy of the entire system.

3.If your boat of transducer is out of the water for a period of time, it may take a short period of time for the transducer to become thoroughly “wetted” when returned to the water. Also, re-entry may cause turbulence, which will create air bubbles in the “eye” of the transducer. The bubbles will disappear in a short time or can be removed by rubbing the transducer “eye” with your fingers while the transducer is in the water.

4.If your instrument should fail to function, be sure to check all the electrical connections before removing the transducer or calling a serviceman.

5.Inspect your transducer cable and make sure that it has not been cut or damaged to the point where it will affect the performance of the transducer. A slight nick or cut, exposing the outer cable, can be repaired by wrapping with electrical tape. A transducer can be damaged if the inner cable and outer cable are allowed to make contact. Such a problem can sometimes be corrected by properly splicing the coaxial cable. This should only be attempted by a qualified service technician.

6.If your LCR is not working properly and you suspect the problem might be in your transducer, we would recommend you borrow a unit from a friend and try it on your boat. If the symptoms are the same, you can almost be certain that the problem is in the transducer.

Image 9
Contents Page Table of Contents Transducer Mounting Options Transducer Mounting ProcedureTransom Mounting Procedure Page Page Page Inside Hull Mounting Procedure Page Installing the LCR Other Mounting Options Installing the CablesPage Test the Installation InstallationTheory of Operation IntroductionUsing the LCR Using the LCR What is Total Screen Update? Total Screen UpdateHow Does Total Screen Update Work? How To Use Total Screen UpdateLCR Operational InstructionsUsing the LCR Automatic or Manual Mode What Zoom Does How To Use ZoomBottom Lock Some Additional Things You Should Know About ZoomBottom Alarm Fish AlarmUsing the LCR Reading will not be seen while in the manual mode Some additional things you should know about the LCR Additional InformationCaring for Your LCR Step Learning to USE Your LCRUsing the LCR Using the LCR Learning to Read the Display Using the LCR Maintenance Maintenance and WarrantyNothing happens when I turn the unit on TroubleshootingThere is no bottom reading visible on the display Unit comes on before I press POWER, and wont turn off Humminbird ONE Year Full Warranty Service Policy Customer Support