Humminbird 955C manual Mounting Screws

Page 12

531569-1_B - 955c ManE.qxp 3/4/2007 5:03 PM Page 6

8.5"

5"

3.6"

1.25"

1

3

2

1 Mounting Screws

Gimbal Mounting Bracket 3

2Washer

5.Set the gimbal bracket aside and drill the four mounting screw holes using a 5/32" (4.0 mm) drill bit.

6a. If the cables must pass through a hole directly beneath the mounting bracket, mark and drill an additional 1" (25 mm) hole centered between the four mounting holes. Route the cables through the 1" hole. Place the hole cover over the mounting surface hole, then use it to mark the position of the two mounting screws.

Remove the hole cover, drill the two mounting holes using a 9/64" bit. Do not install the hole cover at this time.

or...

6b. If the cables cannot be routed directly beneath the mounting bracket, mark and drill a 1" (25 mm) hole that will allow you to run the cables close to the bracket. Pass the cables through the 1" (25

mm) hole, routing the cables through the grommet and pressing the grommet into place. Place the hole cover over the mounting surface hole, then use it to mark the position of the two mounting screws. Remove the hole cover, drill the two mounting holes using a 9/64" (3.5 mm) bit, fill them with marine-grade silicone, then replace the hole cover and insert the #8 Phillips countersink wood screws. Hand-tighten only.

7.Place the mounting bracket on the mounting surface aligned with the drilled holes and fill the mounting holes with marine grade silicone. Insert the four #10 Slotted-Hex wood screws into the mounting holes. Hand-tighten only.

8.If the cable pass through hole is beneath the mounting bracket, you will need to install the hole cover. Place the hole cover over the mounting bracket cable pass thru hole and align with holes drilled in step 6a. Insert the #8 Phillips countersink wood screws. Hand tighten only.

NOTE: Be sure that the cables pass through the slots on the hole cover and that there is enough cable slack to allow for the control head to pivot through its full tilt range. Extra cable slack will also help when connecting/disconnecting the cables.

6

Image 12
Contents 531569-1B 955c ManE.qxp 3/4/2007 503 PM Thank You Table of Contents Menu System Start-Up Options Menu Navigation Menu Tab Views Menu Tab Accessories Menu Tab Series Introduction How GPS and Cartography WorkSoftware Updates Multi-Media Card MMC/SD SlotAccessory Bus Installation OverviewControl Head Installation Basic installation tasks that you must perform includeGimbal Mounting the Control Head 531569-1B 955c ManE.qxp 3/4/2007 503 PM Mounting Screws 531569-1B 955c ManE.qxp 3/4/2007 503 PM 531569-1B 955c ManE.qxp 3/4/2007 503 PM Connecting the Control Head Power Cable to the Boat GPS Receiver Installation Stem Mounting with an Existing 1 14 Thread StemFollow these steps to stem mount the GPS receiver Access Under Mounting Location No Access Under Mounting Location Finish Routing the Cable Check GPS Receiver OperationTesting the System Installation To test the installationGetting Started Using Your 900 Series Powering Up the Control HeadWhat’s On the Display CartographyPOWER/LIGHT Key Key FunctionsView Key View Preset Keys Menu KeyWAY Cursor Control Key Exit Key Info KeyMark Key Goto KeyViews Zoom +/- KeysViews available on your 900 Series are SecondsChart View Views and ReadoutsBirds Eye Instrument View Birds Eye Big Digits ViewBirds Eye Instrument View Bird’s Eye Big Digits View Chart/Bird’s Eye Combo View Traveling measured in degrees from NorthChart/Chart Combo View Chart No Readouts View Chart View VoltageCursor Icon Boat Icon Chart Big Digits View Chart Instrument View Cartography Boat Icon RouteScreen Snapshot View Information Box531569-1B 955c ManE.qxp 3/4/2007 503 PM Chart Orientation Viewing CartographyIntroduction to Navigation Waypoints, Routes and Tracks Save, Edit, or Delete a Waypoint Navigate to a Waypoint or Position Add a Waypoint Target or Trolling GridSave, Edit or Delete a Route Save or Clear a Current Track Edit, Delete or Hide Saved TracksMan Overboard MOB Navigation Menu System Start-Up Options Menu Normal Operation SimulatorNormal Simulator System Status Accessory Test System StatusSelf Test GPS Diagnostic View Navigation X-Press Menu Active SideSplit Position Waypoint Name Cursor to WaypointSave Current Track Save Current RouteClear Current Track Skip Next WaypointCancel Navigation Cancel MOB NavigationTo Cancel MOB Navigation Remove TargetMost recently-created waypoint Select Readouts COG VMG Select Nav Readouts Only on views with 5 selectable readoutsSelectable Data Windows Default Chart View Customized Chart View Screen Snapshot Press Menu Delete ImageDelete All Images To delete an imageNavigation Menu Tab Current TrackSaved Tracks WaypointsWaypoints Submenu contains the following menu choices Routes Trolling Grid Rotation North ReferenceTrackpoint Interval North Reference allows you to have bearingsTrack Min Distance Track Color RangeMap Datum Continuous Navigation Mode Course Projection LineExport All Nav Data Delete All Nav DataChart Menu Tab Chart Detail LevelMap Borders Lat/Lon GridSpot Soundings Navaids on Birds Eye View Shaded DepthSet Simulation Position Set Map Offset Clear Map OffsetAlarms Menu Tab Low Battery AlarmAux. Temp. Alarm Temp. AlarmOff Course Alarm Arrival AlarmDrift Alarm Alarm ToneSetup Menu Tab Units DepthUnits Temp User Mode Units DistanceUnits Speed LanguageTriplog Reset Restore DefaultsAux. Temp.Offset Temp. OffsetSpeed Calibration Local Time ZoneDaylight Saving Time Position FormatTime Format Date FormatDigits Format Nmea Output DemonstrationViews Menu Tab Following views are availableAccessories Menu Tab Using Screen Snapshot531569-1B 955c ManE.qxp 3/4/2007 504 PM Troubleshooting Display Problems Chartplotter Doesn’t Power UpYear Limited Warranty Away from the engine wiringFinding the Cause of Noise Humminbird Service Policy Returning Your Unit for Service Series Chartplotter Accessories Series includeSpecifications Glossary GPS & Navigation TermsGlossary Glossary Glossary Contact Humminbird