Radio Shack TRC-446 owner manual Adjusting the Standing Wave Ratio, Public Address Speaker

Page 9

21-1574.fm Page 9 Thursday, May 13, 1999 4:03 PM

Public Address Speaker

To connect a PA speaker to the CB, use an 8-ohm speaker capable of handling 5 or more watts of power and equipped with an 1/8-inch connector on the cable. Contact your local RadioShack store for a selection of suitable speakers. Plug into PA SP. See “Using the Public Address Function” on Page 14 for oper- ation instructions.

ADJUSTING THE STANDING WAVE RATIO

Most antennas are factory adjusted. However, you can usually improve per- formance by matching the characteris- tics of your antenna system to the CB's RF output power using the built-in SWR meter. The impedance of a CB’s output compared to the impedance of the an- tenna and the antenna cable is typically slightly mismatched. By adjusting this impedance ratio to be as close to 1:1 as possible, you maximize the efficiency of your system.

After you have properly installed the an- tenna and routed its cable, follow these steps to adjust the standing wave ratio

Note: The SWR on some mobile and base-station antennas cannot be changed.

1.Turn on the CB by turning OFF/VOL- UME clockwise until it clicks.

2.Set S/RF/SWR/CAL to CAL.

3.Hold down the microphone's talk button and adjust SWR CAL so the SWR/RF signal meter's needle

points to CAL on the upper SWR scale.

4.Release the microphone's talk but- ton.

5.Set S/RF/SWR/CAL to SWR.

6.Press the microphone's talk button again and note the actual SWR measurement on the upper SWR scale. See the chart on Page 10 for help in interpreting the SWR meter readings.

The SWR value takes into account the actual frequency of the RF signal trans- mitted. Therefore, you will get a different SWR reading from one CB channel to another. Almost all the CB transmis- sions usually fall within an acceptable range. However, for optimum radio per- formance, we recommend that you fine tune the antenna's system based on the channel you use most. If you have no particular channel preference, set your antenna's SWR for maximum perfor- mance on Channel 19.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents TRC-446 Features FCC Information Contents Installation Mounting the Microphone HolderMounting the TRC-446 Antenna Connecting MicrophoneUsing Vehicle Battery Power Installing AN AntennaConnecting an Antenna Selecting an AntennaUsing the CB AS a Base Station Connecting Optional External SpeakersExternal CB Speaker Public Address Speaker Adjusting the Standing Wave RatioSet S/RF/SWR/CAL to CAL Set S/RF/SWR/CAL to SWRStanding Wave Ratio Guidelines Standing Wave Ratio PerformanceRatio Rating Evaluation Noaa Quick Look AT the ControlsTurning on the CB and Receiving Transmissions OperationTransmitting Changing Channels Using the Controls on the MicrophoneListening to Weather Broadcasts Frequency Channel MHzWeather Alert Using the Public Address FunctionTypical Uses For a CB Radio CB Operation TipsBusiness Uses Personal UsesCode Meaning Using Common 10-CODESReducing Noise Maximum RangeTroubleshooting Symptom Check ThatCH9/NOR/CH-19 is set to NOR Care and Maintenance Replacing the Fuses General SpecificationsPublic Address Fm Page 23 Thursday, May 13, 1999 403 PM Vised of the Possibility of Such Damages Limited Ninety-Day Warranty

TRC-446 specifications

The Radio Shack TRC-446 is a classic handheld CB (Citizens Band) radio, well-regarded in the realm of two-way communication devices. Released in the 1980s, it has become a sought-after collector's item due to its impressive features, build quality, and ease of use.

One of the defining characteristics of the TRC-446 is its compact and portable design. Weighing less than many of its contemporaries, it fits comfortably in the hand and is lightweight enough for prolonged use. This makes it an excellent choice for outdoor enthusiasts, truck drivers, and hobbyists alike. Its robust construction ensures that it can withstand the rigors of daily use.

In terms of technology, the TRC-446 operates on the standard 40 channels designated for CB radios in the United States, allowing users to communicate over short distances. It incorporates AM modulation, which was the primary mode of communication for CB radios, ensuring compatibility with a wide range of other devices. The operating range can reach several miles, depending on the terrain, making it ideal for both urban and rural communication.

The user interface is designed for simplicity, featuring a clear display with channel indicators, an easy-to-access volume control, and a squelch knob to eliminate background noise. The push-to-talk button is conveniently placed, providing seamless access during conversations. Additionally, the TRC-446 comes equipped with a built-in microphone, making voice transmission effortless.

Another noteworthy feature is the external antenna jack, which allows for improved communication range. Users can connect various antennas, enhancing their ability to send and receive signals in challenging environments.

The TRC-446 also supports compatibility with additional accessories, such as handsets and speakers, allowing for a more customizable communication experience. The battery life is decent for a handheld device, with options for both rechargeable and disposable batteries, making it versatile for different use cases.

In conclusion, the Radio Shack TRC-446 represents a significant piece of communication technology from the late 20th century. With its reliable performance, user-friendly design, and compatibility with a range of accessories, it remains a cherished model among CB radio enthusiasts. Whether for nostalgia or practical use, the TRC-446 stands out as a testament to the enduring appeal of two-way radio communication.
Top Page Image Contents