Multiquip Model WM45H MIXeR SaFeTY EngIne SaFeTY,  dO nOT mix flammable or explosive substances

Page 8
DANGEROUS
GAS FUMES

Safety Information

MIXeR SaFeTY

 

engIne SaFeTY

 

 

 

dangeR

 

dangeR

 

 

 

neveR operate the equipment in an explosive atmosphere or near combustible materials.An explosion or fi re could result causing severe bodily harm or even death.

dO nOT mix flammable or explosive substances.

WaRnIng

neveR place your hands inside the drum while starting or operating this equipment.

neveR disconnect any emergency or safety devices. These devices are

intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

Before operating mixer, ensure that safety grate is in position and correctly fi tted.

CauTIOn

neveR lubricate components or attempt service on a running machine.

NOTICE

aLWaYS keep the machine in proper running condition.

aLWaYS ensure mixer is on level ground before mixing.

Fix damage to machine and replace any broken parts immediately.

dO nOT tip mixer onto drum mouth when the drum is rotating.

Ensure the drum is rotating while fi lling and emptying the drum.

aLWaYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

Engine fuel exhaust gases contain poisonous carbon monoxide. This gas is colorless and odorless, and can cause death if inhaled.

The engine of this equipment requires an adequate

free fl ow of cooling air. neveR operate this equipment in any enclosed or narrow

area where free fl ow of the air is restricted. If the air fl ow is restricted it will cause injury to people and property and serious damage to the

equipment or engine.

WaRnIng

dO nOT place hands or fingers inside engine compartment when engine is running.

neveR operate the engine with heat shields or guards removed.

Keep fi ngers, hands hair and clothing away

from all moving parts to prevent injury.

dO nOT remove the engine oil drain plug

while the engine is hot. Hot oil will gush out of the oil tank and severely scald any persons in the general area of the mixer.

CauTIOn

neveR touch the hot exhaust manifold, muffl er or cylinder. Allow these parts to cool

before servicing equipment.

Make certain the operator knows how to and is capable of turning the engine OFF in case of an emergency.

NOTICE

neveR run engine without an air fi lter or with a dirty air fi lter. Severe engine damage may occur. Service air fi lter frequently to prevent engine malfunction.

neveR tamper with the factory settings of the engine or engine governor. Damage to the engine or equipment can result if operating in speed ranges above the maximum allowable.

page 8 — WM45H/E PLASTER/MORTAR MIXER • operation and parts manual — rev. #0 (09/27/12)

Image 8
Contents Model wm45H Page Silicosis/respiratory warnings Silicosis WarningTable of Contents WM45H/WM45E Plaster/ Mortar MixerChoose from three easy options Safety Information SaFeTY MeSSageSSaFeTY Symbols Symbol Safety HazardGeneRaL SaFeTY Before servicing equipment MIXeR SaFeTY EngIne SaFeTY dO nOT mix flammable or explosive substances EnvIROnMenTaL SaFeTY FueL SaFeTYTRanSpORTIng SaFeTY Mixer Specifications Engine/Electric Motor SpecificationsDimensions L x W x H ModelDimension in. cm DIMENSIONSMixer Dimensions General information Components Major ComponentsBasic engine Muffler Used to reduce noise and emissionsElectric Motor Voltage Switch Electric Motor Wiring InformationElectric Motor Electric Motor ConnectionPre-inspection Engine/mixer Place both engine ON/OFF switches in the on position Initial Start-up EngineMixing Dumping Initial Start-up Engine/electric motorStarting the Electric motor Shutdown Maintenance Engine Engine MaintenanceEngine Maintenance Schedule First EveryWeekly MaintenanceDaily Maintenance mixer Grease Fittings Zerk Maintenance Electric MotorDrum Head Seals Drum Bearing Bracket LubricationMixer Cleaning Main Gear and Drive Pinion AlignmentInspect Tooth Contact Between Main Gear and Drive Pinion Gear LubricationTroubleshooting Engine Troubleshooting engineTroubleshooting Engine/mixer Troubleshooting MixerSymptom Possible problem Solution Troubleshooting electric MotorWiring diagram Electric motor Electric Motor Wiring DiagramPage Explanation of Code in Remarks Column Suggested Spare Parts Qty DescriptionNameplate and Decals DECAL, do not Smoke Decal MQ LogoDecal Push to Stop Front Rear Drum GrateHand Grip TrunnionPaddle Shaft Assy Paddle Shaft INSERT, Paddle ARMPaddle ARM, Engine END WASHER, Flat 1/2Frame Assy SWITCH, PUSH-PULL W/O Knob Wire HarnessGRIP, Rubber Black HANDLE, FRONT-LEFTEngine cover Assy Latch Assy Retainer ChainEngine House Assy Engine/GUARD Assy GX160UT1HX2 ENGINE-4.8 H.P. Honda Flatwasher 5/16Lockwasher 5/16 Pinion GearElectric motor Assy Pillow Block Drive Pinion GearFlat Washer 5/16 Lock Washer 5/16Terms and Conditions of Sale Parts FReIgHT pOLICYPage HERE’S HOW to GET Help