Pioneer PDR-509 manual Connecting Up for Analog Playback & Recording, Supplied stereo, audio cords

Page 11

Connecting Up for Analog Playback & Recording

CONTROL IN

CONTROL OUT

Connecting Up

Connecting Up for Analog Playback & Recording

Before you start, make sure that all the components are	recorder (check the instruction manual that came with your
switched off and disconnected from the wall outlet.	amplifier if you’re unsure about which terminals to use).
Next, connect this unit to your amplifier/receiver using the	Using this set up you can make recordings from any other
two sets of supplied audio leads—one set for playback,	component connected to the amplifier, via the analog
the other for recording. On the rear panel of your amplifier	inputs of this unit.
find an unused set of inputs/outputs for a tape/MD

PDR–509 CD-Recorder

AC IN

LINE IN

LINE OUT CONTROL

DIGITAL IN

DIGITAL OUT

R	L	R	L	OPTICAL	COAXIAL	OPTICAL	COAXIAL
				IN

R

L

R

L

Supplied stereo

audio cords

To wall outlet.

Getting Set Up

R

L

R

L

MD/TAPE

OUTPUT INPUT

REC PLAY

L

R

OUT

CONTROL

Pioneer ë out

Amplifier

Note: Rear panel show is that of U.S. and Canadian models; others may look slightly different.

Connecting Other Pioneer

ëComponents

If you are using a Pioneer amplifier or receiver that has this feature, you can control this unit with the multi- remote controller that came with your amplifier/receiver. The advantage of this is that you can use a single remote control to operate several components. Check the instruction manual that came with your amplifier or receiver for more information on using its remote as a multi-controller.

Use a commercially available cord with a mono mini- plug at either end to connect the

terminal of the amplifier/receiver to the terminal of this unit.

Make sure that at least one set of analog terminals is connected to the amplifier when using ë control cords.

11

Image 11

Contents COMPACT DISC RECORDER PDR-509Operating Instructions RISK OF ELECTRIC SHOCK DO NOT OPEN IMPORTANT SAFETY INSTRUCTIONSFOR USE IN THE UNITED IMPORTANT NOTICE For U.S. modelFor U.S. model Information to UserCLASS LASER PRODUCT Features of the PDR-509CD RecorderBefore You Start INFRINGEMENT OF COPYRIGHT For U.K. modelAdditional Recording Features ContentsConnecting Up Additional Playback FeaturesChecking What’s in the Box Using This ManualPutting the Batteries in the Remote Control Set UpCleaning external surfaces Hints on InstallationAvoiding condensation problems Getting Set UpCD-Rewritablediscs About CD, CD-Rand CD-RWDiscsPlayback-onlyCDs CD-RecordablediscsGetting Set Up Handling discsStoring discs Discs to avoidUsing the digital outputs Connecting Up for Digital Playback & RecordingConnecting Up Using the digital inputsaudio cords Connecting Up for Analog Playback & RecordingConnecting Other Pioneer ëComponents Supplied stereoi o a s d f g Front PanelWhat’s What w e r t yWhat’s What Remote ControlBasic Playback and Recording What’s What Displayp q w e 8 ty uBasic Playback and Recording Switching On for the First Time1 Switch the POWER to ON 6 When youre done, press 7 stopPUSH Choosing a Track to PlaySkipping Tracks Repeating TracksTIME DISP OFF Press DISP OFF to switch between display modesShowing Disc Information TIMEAutomatic digital Introduction to CD RecordingRecording modes Digital recording restrictionsDisc type display Digital signal interruptionsPower interruptions Digital recording from DAT6 If youre done, press 7 stop Recording One Track from a Digital SourceLoad a CD-Ror CD-RWdisc Play the sourcedigital inputs Recording All Tracks from a Digital Source1 Load a CD-Ror CD-RWdisc Press INPUT SELECTOR to choose one of the4 Play the source Automatically Recording and Finalizing a DiscBasic Playback and Recording 1 Load a CD-Ror CD-RWdiscdigital inputs 3 Press RECORD REC on the remote control7 When youre done, press 7 stop Manually Recording a Digital SourceIf the recorder is stopped, press MONITOR or Setting the Digital Recording LevelRECORD REC on the remote control 2 3,4controls 8 When youre done, press 7 stopRecording an Analog Source 2 Press INPUT SELECTOR to choose analog input3 Press 3 play to start playback Additional Playback FeaturesProgramming the Track Order During playback or stop mode, press PROGRAMRANDOM Fading In and Fading OutPlaying Tracks at Random Playing a Disc with Skip IDsThe display prompts you to confirm Additional Recording FeaturesSetting skip IDs Skipping Unwanted TracksClearing skip IDs Press SKIP PLAY to switch off skip play modeWhen youre finished, stop the disc and 3 3 2,32 Start recording Numbering TracksRecording Fade Ins and Fade Outs FADERPress RECORD FeaturesChecking Whats at the End of a Disc Recording Blank Sections1 Start the source component playing 3 To switch off monitoring, press MONITOR againMonitoring a Source Checking for Digital Copy Protection3 Press 8 pause to start finalization Finalizing a Disc1 Load the CD-Ror CD-RWyou want to finalize 2 Press FINALIZEmote control to change the erase option When a non-finalizeddisc is loaded 1 Press ERASEErasing a CD-RWDisc 2 Use the jog dial or press 4 and ¢ on the re1 Press ERASE When a finalized disc is loadedERASE 8jog dialAdditional Information Understanding Display MessagesAdditional TroubleshootingAdditional Information InformationRemedy SymptomAdditional Information Cause2. Audio unit Specifications5. Accessories 1. GeneralPIONEER ELECTRONIC CORPORATION hhhhhhhhhhhhh We Want You Listening For A Lifetime