Pioneer PDR-509 manual IMPORTANT NOTICE For U.S. model, Information to User, For Use In The United

Page 3
IMPORTANT NOTICE [For U.S. model]

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

IMPORTANT NOTICE [For U.S. model]

The serial number for this equipment is located on the rear panel. Please write this serial number on your enclosed warranty card and keep it in a secure area. This is for your security.

[For Canadian model]

This Class B digital apparatus complies with Canadian ICES-003.

[Pour le modèle Canadien]

Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

[For Canadian model]

CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS (POLARIZED) PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.

ATTENTION: POUR PREVENIR LES CHOCS ELECTRIQUES NE PAS UTILISER CETTE FICHE POLARISEE AVEC UN PROLONGATEUR, UNE PRISE DE COURANT OU UNE AUTRE SORTIE DE COURANT, SAUF SI LES LAMES PEUVENT ETRE INSEREES A FOND SANS EN LAISSER AUCUNE PARTIE A DECOUVERT.

[For U.S. model]

DANGER – LASER RADIATION WHEN OPEN. AVOID DIRECT EXPOSURE TO BEAM.

This caution can be found on the rear panel of the unit.

CAUTION:

¦Use of controls or adjustments or performance of procedures other than those specified herein hazardous radiation exposure.

¦The use of optical instruments with this product will increase eye hazard.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

–Reorient or relocate the receiving antenna.

–Increase the separation between the equipment and receiver.

–Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

–Consult the dealer or an experienced radio/TV technician for help.

CAUTION:

This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

Information to User

Alteration or modifications carried out without appropriate authorization may invalidate the user’s right to operate the equipment.

IMPORTANT

amp socket as this can result in

coloured red.

 

electric shock. The plug or adaptor of

Do not connect either wire to the earth

 

 

 

 

FOR USE IN THE UNITED

the distribution panel should be

 

terminal of a three-pin plug.

 

KINGDOM

 

provided with a 5 amp fuse. As the

NOTE

 

 

colours of the wires in the mains lead

 

 

 

After replacing or changing a fuse, the

 

The wires in this mains lead are

of this appliance may not correspond

 

coloured in accordance with the

with coloured markings identifying

fuse cover in the plug must be replaced

 

following code:

 

the terminals in your plug, proceed as

with a fuse cover which corresponds to

 

Blue :

Neutral

follows:

the colour of the insert in the base of

 

The wire which is coloured blue must

the plug or the word that is embossed

 

Brown :

Live

 

on the base of the plug, and the

 

If the plug provided is unsuitable for

be connected to the terminal which is

 

appliance must not be used without a

 

marked with the letter N or coloured

 

your socket outlets, the plug must be

fuse cover. If lost, replacement fuse

 

black.

 

cut off and a suitable plug fitted.

 

covers can be obtained from your dealer.

 

The wire which is coloured brown

 

 

 

 

The cutoff plug should be disposed of

Only 5 A fuses approved by B.S.I. or

 

must be connected to the terminal

 

and must not be inserted into any 13

A.S.T.A. to B.S. 1362 should be used.

 

which is marked with the letter L or

 

 

 

 

 

 

 

 

 

 

 

 

3

 

 

 

 

Page 2 Page 4
Image 3
Page 2 Page 4
Contents PDR-509 Operating InstructionsCOMPACT DISC RECORDER RISK OF ELECTRIC SHOCK DO NOT OPEN IMPORTANT SAFETY INSTRUCTIONSFOR USE IN THE UNITED IMPORTANT NOTICE For U.S. modelFor U.S. model Information to UserCLASS LASER PRODUCT Features of the PDR-509CD RecorderBefore You Start INFRINGEMENT OF COPYRIGHT For U.K. modelAdditional Recording Features ContentsConnecting Up Additional Playback FeaturesChecking What’s in the Box Using This ManualPutting the Batteries in the Remote Control Set UpCleaning external surfaces Hints on InstallationAvoiding condensation problems Getting Set UpCD-Rewritablediscs About CD, CD-Rand CD-RWDiscsPlayback-onlyCDs CD-RecordablediscsGetting Set Up Handling discsStoring discs Discs to avoidUsing the digital outputs Connecting Up for Digital Playback & RecordingConnecting Up Using the digital inputsaudio cords Connecting Up for Analog Playback & RecordingConnecting Other Pioneer ëComponents Supplied stereoi o a s d f g Front PanelWhat’s What w e r t yRemote Control Basic Playback and RecordingWhat’s What What’s What Displayp q w e 8 ty uBasic Playback and Recording Switching On for the First Time1 Switch the POWER to ON 6 When youre done, press 7 stopPUSH Choosing a Track to PlaySkipping Tracks Repeating TracksTIME DISP OFF Press DISP OFF to switch between display modesShowing Disc Information TIMEAutomatic digital Introduction to CD RecordingRecording modes Digital recording restrictionsDisc type display Digital signal interruptionsPower interruptions Digital recording from DAT6 If youre done, press 7 stop Recording One Track from a Digital SourceLoad a CD-Ror CD-RWdisc Play the sourcedigital inputs Recording All Tracks from a Digital Source1 Load a CD-Ror CD-RWdisc Press INPUT SELECTOR to choose one of the4 Play the source Automatically Recording and Finalizing a DiscBasic Playback and Recording 1 Load a CD-Ror CD-RWdiscdigital inputs 3 Press RECORD REC on the remote control7 When youre done, press 7 stop Manually Recording a Digital SourceIf the recorder is stopped, press MONITOR or Setting the Digital Recording LevelRECORD REC on the remote control 2 3,4controls 8 When youre done, press 7 stopRecording an Analog Source 2 Press INPUT SELECTOR to choose analog input3 Press 3 play to start playback Additional Playback FeaturesProgramming the Track Order During playback or stop mode, press PROGRAMRANDOM Fading In and Fading OutPlaying Tracks at Random Playing a Disc with Skip IDsThe display prompts you to confirm Additional Recording FeaturesSetting skip IDs Skipping Unwanted TracksClearing skip IDs Press SKIP PLAY to switch off skip play modeWhen youre finished, stop the disc and 3 3 2,32 Start recording Numbering TracksRecording Fade Ins and Fade Outs FADERPress RECORD FeaturesChecking Whats at the End of a Disc Recording Blank Sections1 Start the source component playing 3 To switch off monitoring, press MONITOR againMonitoring a Source Checking for Digital Copy Protection3 Press 8 pause to start finalization Finalizing a Disc1 Load the CD-Ror CD-RWyou want to finalize 2 Press FINALIZEmote control to change the erase option When a non-finalizeddisc is loaded 1 Press ERASEErasing a CD-RWDisc 2 Use the jog dial or press 4 and ¢ on the re1 Press ERASE When a finalized disc is loadedERASE 8jog dialAdditional Information Understanding Display MessagesAdditional TroubleshootingAdditional Information InformationRemedy SymptomAdditional Information Cause2. Audio unit Specifications5. Accessories 1. GeneralPIONEER ELECTRONIC CORPORATION hhhhhhhhhhhhh We Want You Listening For A Lifetime
Top Page Image Contents