Page 7
✘DON’T...
❖ Use in a place exposed to high temperatures or humidity, including near radiators and other heat- generating appliances.
❖ Place on a window sill or other place where the player will be exposed to direct sunlight.
❖ Use in an excessively dusty or damp environment.
❖ Place directly on top of an amplifier, or other component in your stereo system that becomes hot in use.
❖ Use near a television or monitor as you may experience interference—especially if the television uses an indoor antenna.
❖ Use in a kitchen or other room where the player may be exposed to smoke or steam.
❖ Place on an unstable surface, or one that is not large enough to support all four of the unit’s feet.
Before You Start
Hints on Installation
We want you to enjoy using the PDR–509 for years to come, so please bear in mind the following points when choosing a suitable location for it:
✔DO...
❖ Use in a well-ventilated room.
❖ Place on a solid, flat, level surface, such as a table, shelf or stereo rack.
Avoiding condensation problems
Condensation may form inside the player if it is brought into a warm room from outside, or if the temperature of the room rises quickly. Although the condensation won’t damage the player, it may tempo- rarily impair its performance. For this reason you should leave it to adjust to the warmer temperature for about an hour before switching on and using.
Maintaining Your CD Recorder
Getting Set Up
Cleaning external surfaces
To clean the compact disc recorder, wipe with a soft, dry cloth. For stubborn dirt, wet a soft cloth with a mild detergent solution made by diluting one part detergent to
5 or 6 parts water, wring well, then wipe off the dirt. Use a dry cloth to wipe the surface dry. Do not use volatile liquids such as benzene and thinner which may damage the surfaces.
CD lens cleaner
The compact disc recorder's pickup lens should
not become dirty in normal use, but if for some reason it should malfunction due to dirt or dust, consult your nearest Pioneer authorized service center. Although lens cleaners for compact disc recorders are commercially available, we do not recommend using them since some may damage the lens.
Moving the unit
If you need to move the unit, first switch it off and unplug from the wall outlet. Never lift or move the unit during playback or recording—the disc rotates at a high speed and may be damaged.
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest PIONEER authorized service center or your dealer for a replacement.
Storing Optical Cable
When storing optical cable, coil loosly as shown below. The cable may be damaged if bent around sharp corners.
More than
+5-14/16in. = (15cm)
Contents
Operating Instructions
PDR-509
COMPACT DISC RECORDER
RISK OF ELECTRIC SHOCK DO NOT OPEN
IMPORTANT SAFETY INSTRUCTIONS
FOR USE IN THE UNITED
IMPORTANT NOTICE For U.S. model
For U.S. model
Information to User
CLASS LASER PRODUCT
Features of the PDR-509CD Recorder
Before You Start
INFRINGEMENT OF COPYRIGHT For U.K. model
Additional Recording Features
Contents
Connecting Up
Additional Playback Features
Checking What’s in the Box
Using This Manual
Putting the Batteries in the Remote Control
Set Up
Cleaning external surfaces
Hints on Installation
Avoiding condensation problems
Getting Set Up
CD-Rewritablediscs
About CD, CD-Rand CD-RWDiscs
Playback-onlyCDs
CD-Recordablediscs
Getting Set Up
Handling discs
Storing discs
Discs to avoid
Using the digital outputs
Connecting Up for Digital Playback & Recording
Connecting Up
Using the digital inputs
audio cords
Connecting Up for Analog Playback & Recording
Connecting Other Pioneer ëComponents
Supplied stereo
i o a s d f g
Front Panel
What’s What
w e r t y
Basic Playback and Recording
Remote Control
What’s What
What’s What
Display
p q w e
8 ty u
Basic Playback and Recording
Switching On for the First Time
1 Switch the POWER to ON
6 When youre done, press 7 stop
PUSH
Choosing a Track to Play
Skipping Tracks
Repeating Tracks
TIME DISP OFF
Press DISP OFF to switch between display modes
Showing Disc Information
TIME
Automatic digital
Introduction to CD Recording
Recording modes
Digital recording restrictions
Disc type display
Digital signal interruptions
Power interruptions
Digital recording from DAT
6 If youre done, press 7 stop
Recording One Track from a Digital Source
Load a CD-Ror CD-RWdisc
Play the source
digital inputs
Recording All Tracks from a Digital Source
1 Load a CD-Ror CD-RWdisc
Press INPUT SELECTOR to choose one of the
4 Play the source
Automatically Recording and Finalizing a Disc
Basic Playback and Recording
1 Load a CD-Ror CD-RWdisc
digital inputs
3 Press RECORD REC on the remote control
7 When youre done, press 7 stop
Manually Recording a Digital Source
If the recorder is stopped, press MONITOR or
Setting the Digital Recording Level
RECORD REC on the remote control
2 3,4
controls
8 When youre done, press 7 stop
Recording an Analog Source
2 Press INPUT SELECTOR to choose analog input
3 Press 3 play to start playback
Additional Playback Features
Programming the Track Order
During playback or stop mode, press PROGRAM
RANDOM
Fading In and Fading Out
Playing Tracks at Random
Playing a Disc with Skip IDs
The display prompts you to confirm
Additional Recording Features
Setting skip IDs
Skipping Unwanted Tracks
Clearing skip IDs
Press SKIP PLAY to switch off skip play mode
When youre finished, stop the disc and
3 3 2,3
2 Start recording
Numbering Tracks
Recording Fade Ins and Fade Outs
FADER
Press RECORD
Features
Checking Whats at the End of a Disc
Recording Blank Sections
1 Start the source component playing
3 To switch off monitoring, press MONITOR again
Monitoring a Source
Checking for Digital Copy Protection
3 Press 8 pause to start finalization
Finalizing a Disc
1 Load the CD-Ror CD-RWyou want to finalize
2 Press FINALIZE
mote control to change the erase option
When a non-finalizeddisc is loaded 1 Press ERASE
Erasing a CD-RWDisc
2 Use the jog dial or press 4 and ¢ on the re
1 Press ERASE
When a finalized disc is loaded
ERASE
8jog dial
Additional Information
Understanding Display Messages
Additional
Troubleshooting
Additional Information
Information
Remedy
Symptom
Additional Information
Cause
2. Audio unit
Specifications
5. Accessories
1. General
PIONEER ELECTRONIC CORPORATION
hhhhhh
hhhhhhh
We Want You Listening For A Lifetime