Navman 4432 Secondary alarm wiring option Fish 4433 only, Fuel kit wiring Fish 4433 only

Page 28

Secondary alarm wiring option (FISH 4433 only)

Green Wire: Use this to connect a secondary alarm indicator such as a flashing light or external beeper with a built-in drive circuit. See the Auto power wiring diagram.

If the external beeper or light requires more than 200 mA total, fit a relay. Consult your Navman dealer for more advice.

Fuel kit wiring (FISH 4433 only)

See the Fuel Kit Installation Guide for information about the fuel transducer cable.

Wire the power cable for Auto power (as described in this section) to make sure the fuel counter starts as soon as the engine starts.

For twin engine installation, a T-connector needs to be installed on the fuel transducer cable.

Auto power option

Black wire: Connect this to the negative

Auto power option

battery terminal.

To ignition system

Red wire: Connect this to the positive battery

Fuse

White (NMEA out)

terminal after the main switch. Fit a 1 Amp fuse

Ignition

as shown.

switch

Yellow wire: To enable the engine hours

Yellow

counter and fuel counter; and to start the

Fuse

Red

fishfinder automatically when the ignition

External Beeper

is turned on, connect the yellow wire to the

Main

or Light

Green

ignition system through a 1 Amp fuse.

switch

Note: The fishfinder cannot be turned off while

Black

the ignition is on.

12 V DC

Through hull transducers

Through hull transducers are supplied wth ‘Y’ adapter cable for connection of both transducers into top socket with blue nut.

8 pin

phono

Speed/Temperature through hull transducer

Through hull depth transducer

FISH 4432/4433 Installation and Operation Manual

NAVMAN

30

Image 28

Contents Pilot Contents Navman Introduction Benefits of the Fish 4432/4433How the Fish 4432/4433 works Basic OperationKey Names Power On / Auto Power Power OffBacklight Adjustment Key OperationSimulate Mode Setting up the Fish 4432/4433Manual, Fishing and Cruising Modes Setup menu and options Setup System Auto power offBacklight Snooze Mode Factory resetFish symbols Pulse powerScroll speed Digit sizeSetup Logs Reset trip distReset total dist Reset engine hoursSetup Alarms Alarms automatically re-enableSetup Units Flashing light and/or external beeperSetup Comms 4433 only Setup CalibrateNmea data Nmea OutTemperature Temp filterFuel Keel offsetUsing the Fish 4432/4433 Interpreting the displayStrength of echoes Bottom typesFrequency and cone width ShadowsExample of shadows Depth 83 kHz 200 kHzWhen to use 83 kHz Single and Dual frequency fishfinding When to use 200 kHzAuto frequency KHz display 200/83 Khz displayFish symbols On Fish detection and display Where to find fishFish arches Changing between Cruising, Fishing and Manual GainObtaining the best results Range Changing the Range ModeZoom Range and Zoom Offset Displays Display menuSonar display Data headerSonar History Sonar Zoom displayScope Bottom lockSonar 83/200 display Sonar Bottom displaySonar A-Scope display Scope perspective view Fish recognitionFuel display 4433 only Data display About displayWiring Options Basic wiringNmea wiring Option Fish 4433 only Wire FunctionSecondary alarm wiring option Fish 4433 only Fuel kit wiring Fish 4433 onlyAuto power option Through hull transducersWhat comes with this product? Options and AccessoriesMounting and removing the display unit Flush Mounting Removing the display unitBracket Mounting Systems of several instruments 4433 0nlyCleaning and maintenance RepeatAppendix a Specifications Specifications FishAppendix B Dimensions Appendix C Troubleshooting Fishfinder won’t turn onFishfinder won’t turn off Fishfinder operates erraticallyBottom is not displayed Bottom is displayed too far up the screenTwin engine installation shows only one flow rate Flow indicates no fuel or low fuelErratic Fuel Flow readings There is no reading for fuel economyHow to contact us OceaniaFish 4 432 / 4