Furuno 1933C Display Brilliance, Panel Brilliance, Hue, Display brilliance, panel brilliance

Page 21

1. OPERATIONAL OVERVIEW

1.4Display Brilliance, Panel Brilliance, Hue

You can adjust display brilliance, panel brilliance and hue as shown below.

1.4.1Display brilliance, panel brilliance

1.Press the [POWER/BRILL] key momentarily. A set of soft keys for adjustment of brilliance and hue appear.

Active soft key is highlighted.

12/LP 3nm

H-UP

°BRILL

319.9 M CONTST

34° 22.

3456'N

359.9° M

TBRILLP NU

 

080° 22.

3456'E

19.9 kt

CONTST99.9 nm

 

 

 

 

 

 

DISPLY

BRILL

PANEL

BRILL

HUE

RADAR

STBY

16.0nm

WP-002 FISH

DISPLY

BRILL

PANEL

BRILL

HUE

RADAR

STBY

DISPLAY BRILLIANCE

RETURN

8

+ 359.9 ˚R

 

11.70nm

DISPLAYBRIDGEBRILLIANCE

8

RETURN

Radar Display

Plotter Display

Brilliance adjustment soft keys

2.Press the DISPLY BRILL or PANEL BRILL soft key as appropriate. An adjustment window appears at the bottom of the screen. This window shows the name of the item selected for adjustment plus current brilliance level, by bar graph.

DISPLAY BRILLIANCE

8

Display brilliance

PANEL BRILLIANCE

8

Panel brilliance

Display brilliance and panel brilliance windows

3.Adjust the [ENTER] knob, clockwise to raise the setting or counterclockwise to decrease it. You may also use the soft key pressed at step 2. Eight levels of display brilliance and panel brilliance are available.

4.Hit the RETURN soft key to finish.

Note 1: If the unit is turned off with minimum brilliance, the screen will be dark at the next power-up. Press the [POWER/BRILL] key consecutively to adjust the brilliance.

Note 2: This equipment does not have a contrast control.

1-7

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Page R 0 0 Safety Instructions Table of Contents Iii Plotter Operation Video Sounder Operation Customizing Your Unit Data Transfer ViiViii ForewordModel Output Range Radar FeaturesSingle-unit NavNet system Model 1833C/1933C/1943C Single-unit NavNet system Model 1833C/1933C/1943CSingle-unit NavNet system GD-1900C Single-unit NavNet system GD-1900CTwo-unit NavNet system XiiTwo-unit NavNet system Three-or-more-unit NavNet systemOperational Overview Display unit controls Operating ControlsOverview of display unit controls Control panelDisplay unit Soft keys12/LP 3nm Radar and plotter displaysRemote controller Remote controllerChart card and card remover Inserting a Chart CardStartup sequence Turning the Unit On/OffDisplay Brilliance, Panel Brilliance, Hue Brilliance adjustment soft keysDisplay brilliance, panel brilliance Display brilliance and panel brilliance windowsHue window 2 HueDisplay modes Selecting a DisplayDisplay screens Screen type and available display screenSelecting a display Display screen selection windowRadar combination screen selection window To adjust plotter Switching control in combination and overlay screensSelecting image source Select source menuRadar source and sounder source windows Cursor, cursor data Trackball, CursorEntering the MOB Mark, Setting MOB as Destination MOB conceptMOB mark messages Data Boxes Showing, hiding data boxes with soft keyData boxes Temporarily erasing a data box Rearranging data boxesExecuting a function Function Keys16.0 nm Function keysSimulation Display Simulation setup menuRadar NavNet display unit-generated echoesPlotter Sounder + 359.9 ˚R Radar Display12/ LP Radar displayAdjusting the Gain TuningTuning window Transmitting, Stand-byGain sensitivity window Gain adjustment soft keysSEA setting window Adjusting the A/C SEAReducing Sea Clutter How the A/C SEA worksAdjusting the A/C Rain Rain setting windowReducing Precipitation Clutter Range Scale Range scales nm, smRange scales km Pulselength Signal process soft keysPresentation Mode Selecting a presentation modeRadar display soft keys Course-up presentation mode Head-up presentation modeDescription of presentation modes Head-up HUTrue motion presentation mode North-up presentation modeNorth-up NU True motion TMMeasuring the Range Measuring range by range ringsRadar display soft keys Measuring range by cursor How to measure range to a target with the cursorEBL/VRM soft keys Measuring range by VRMMeasuring the Bearing Erasing an EBL, EBL indication How to measure bearing with the EBLErasing EBL/VRM data boxes Hiding EBL/VRM data boxesReducing Noise Interference Erasing the Heading Line, North MarkerRadar interference Rejecting Radar InterferenceZooming in on radar targets ZoomZooming in on ARP, TTM targets ZoomManual shift Shifting the PictureTarget no. selection window Shifting the picture manuallyAuto ship speed setting window Setting automatic shift maximum speedAutomatic shift Automatic shiftUsing the Offset EBL Predicting collision coursePredicting collision course with the offset EBL Measuring range and bearing between two targets Measuring range & bearing between two targetsTrail time Echo TrailsSample echo trails Trail soft keysStarting echo trails Trail gradationMultitone and monotone trails Trail mode window Echo trail modeTrail color Trail color windowTypes of echo stretch Echo StretchEffect of echo averaging Echo AveragingTarget soft keys Outputting TLL DataGuard Alarm Setting a guard alarm zoneHow to set a guard alarm zone Cancelling the guard alarm When the alarm is violated…Watchman Setting watchman stand-by intervalHow watchman works Turning on/off watchmanSecond-trace echoes Suppressing Second-trace EchoesWaypoint marker Waypoint MarkerDisplay accuracy is affected by the following 26 ARP, TTM OperationARP setup menu Activating/deactivating ARP, TTMARP target info window Acquiring and tracking targets ARP ARP plot symbolsManual acquisition Automatic acquisitionDisplaying target number ARP, TTM Automatic acquisition areaARP target number Terminating tracking of ARP targets Cancel all targets windowTerminating tracking of selected targets Terminating tracking of all targetsSetting vector attributes ARP What is a vector?Vector reference, vector time Displaying past position ARP Past position displaysHistory interval window ARP target data 26.7 ARP, TTM target dataCPA window 26.8 CPA/TCPA alarm ARPCanceling a lost target Lost target alarm ARPTcpa window Lost target markInterpreting the Radar Display GeneralMinimum and maximum ranges Bearing resolution Radar resolutionRange resolution Bearing accuracyMultiple echoes False echoesMultiple echoes Sidelobe echoesVirtual image Virtual imageShadow sectors Shadow sectorsSart Search and Rescue Transponder Appearance of Sart signal on the radar displayGeneral remarks on receiving Sart General procedure for detecting Sart responseRacon Radar Beacon Appearance of racon signal on the radar displaySEA control Rain controlPlotter Displays Full-screen plotter displayFull-screen plotter display Contents of nav data window Nav data window001WPT Compass display Compass displaySetting the range for the XTE monitor Reading the XTE cross-track error monitorXTE range setting window Soft keysHighway display Highway displayNav data displays Nav data displayNorth-up Plotter display, north-up modeCourse-up Plotter display, auto course-up modeAuto course-up Plotter display, course-up mode, destination setChart Scale Charts scalesShifting the Display Chart Cards Chart card overviewChart icons and their meanings Indices and chart enlargement Sample chart Japan, showing indicesWhen a chart cannot be displayed Furuno and NavCharts charts Chart symbolsData for aids to navigation Plotter display, showing port service display Port service icons NavCharts onlyCursor and data display MAP chartsObjects window Example of caution area windowIcon data Lighthouse iconObject windows Sample lighthouse data Tide informationObjects window Date window Tide windowDisplaying track Working with TrackOwn ship track Track control menuTarget track Stopping, restarting plotting of own ship trackChanging track color Own ship’s trackOwn ship track color window Track plotting method Track plotting method and interval for own ship trackInterval window Track plotting intervalTrack memory window Changing own ship track/mark distribution settingErasing track Erasing own ship track by areaErase menu Erase track by color window Erasing own ship track by colorErasing all own ship track Erasing all target tracksEntering a mark, line Marks, LinesChanging mark attributes Marks & lines menuMarks shape window Selecting line typeMarks§& lines menu Lines style windowErasing an individual mark Erasing marks, linesErasing an individual line Erasing marks, lines by areaEntering waypoints WaypointsEntering a waypoint at own ship position Entering a waypoint with the cursorWaypoint mark color selection window Waypoint mark shape selection windowEntering a waypoint by range and bearing Entering a waypoint from the waypoint list Editing waypoint dataAlphanumeric and local waypoint lists Editing waypoint data from the waypoint listPlotter display Editing a waypoint from the plotter displayErasing a waypoint directly from the plotter display Erasing waypointsErasing a waypoint from the menu Erasing a waypoint from the waypoint listChart details menu Changing waypoint mark size FURUNO, NavChartsAlphanumeric list Searching waypointsCreating routes RoutesEntering a route with existing waypoints Route menuEntering a route with the cursor New route entry screenCreating voyage-based routes Save route menuSave route window Displays for entry of time, distance interval For manual entry of waypoints, do the followingTo stop recording waypoints and save the route Connect route window Connecting routesInserting a waypoint from the route list Inserting waypointsEdit route menu Waypoint list for editing a route local listInserting a waypoint in an intermediate location on a route Inserting a waypoint from the plotter displayErasing routes Removing waypoints from a routeRemoving a waypoint from the route list Removing a waypoint from the plotter displayNavigating to a quick point NavigationSelecting quick point entry method Go to method windowNavigating to multiple quick points Navigating to waypointsSelecting a waypoint from the plotter display Selecting a waypoint from the waypoint listPort services and sample port list Navigating to ports, port services NavCharts onlySample filling station locations southern Italy Selecting the route to follow Following a routePlotter display, route selected as destination Navigating waypoints in reverse orderExample of when to restart navigation Restarting navigationLog display Switching waypoints Setting speed for ETA calculationAutomatic waypoint switching methods Select speed for ETA windowCanceling route navigation Audio alarm on/off AlarmsPlotter alarm menu Audio alarm windowArrival alarm How the arrival alarm worksArrival alarm window Anchor watch alarm How the anchor watch alarm worksAnchor watch alarm window Speed alarm XTE Cross-Track Error alarmHow the XTE alarm works XTE alarm windowProximity alarm Proximity alarm windowProximity mark Trip alarm window Trip alarmPlotter alarm menu, Alarm informationPlotter alarm messages and their meanings Alarm messagesGeneral setup menu, Resetting Trip DistanceUnderwater conditions and video sounder display Principle of OperationDisplay mode window Sounder DisplaysSelecting a sounder display Description of sounder displays 120Single-frequency display Indications on the single frequency displayDual-frequency display KHz picture Dual-frequency displaySounding area and transmission frequency Marker-zoom displayMarker-zoom display plus normal sounder display Bottom-zoom displayBottom-zoom display plus normal sounder display Bottom-lock display plus normal sounder display Bottom-lock displayBottom discrimination display Bottom discrimination displayScope display display only Scope displaySelecting screen split method in combination displays How to use the Split soft key example dual frequency displayAutomatic Sounder Operation How to enable automatic sounder operationHow the automatic sounder works Types of automatic sounder modesAdjusting the gain Selecting the manual modeManual Sounder Operation Selecting display rangeShifting the range Gain windowShift concept Measuring Depth, Time How to measure depth and timeReducing Interference Types of interferenceNoise limiter window Reducing Low Level Noise Appearance of clutterClutter window Signal level window Erasing Weak EchoesAppearance of weak echoes Color bar 16 color when white marker function is active White MarkerWhite marker window Picture Advance Speed Advancement independent of ship’s speedPicture advance window Advancement synchronized with ship’s speed How the speed-dependent picture advance mode worksHue no. and background and echo colors Display ColorsAlarm audio window Sounder alarm menuFish alarm Bottom alarmBottom alarm window Fish alarm windowFish alarm B/L window Fish alarm B/LWater temperature alarm window Water temperature alarmSounder alarm menu When an alarm setting is violatedSounder alarm messages and their meanings Water Temperature GraphZero line Interpreting the Sounder DisplayBottom echo Zero lineSurface noise/Aeration Fish school echoesFish school echoes Surface noise/aerationGeneral setup menu General SetupOn next Contents of general setup menuRadar display setup Radar SetupContents of general setup menu con’t from previous Radar display setup menuCon’t on next Contents of radar display setup menuContents of radar display setup menu con’t from previous Radar range setup menu Radar range setupFunction key setup Radar function key menuRadar function key options Menu Item Function Function Key Radar function keysPlotter Setup Plotter setup menu Contents of plotter setup menuNavigation options Function key setup Plotter function key menuPlotter function key options RUL Plotter function keysChart Setup Chart offsetPlotter display, chart offset selected Chart details menu FURUNO, NavCharts FURUNO, NavCharts chart attributesContents of chart details menu FURUNO, NavCharts Contour line menu FURUNO, NavCharts MAP chart attributesChart details menu C-MAP Cntour Line soft keyContents of chart details menu C-MAP Settings description Depth Info soft keyDepth info menu C-MAP Data box menu Data Boxes SetupHot page setup menu Hot Page SetupHOT Hot page setup menu, Split X 3 screen, sub screen selectionNavigator Setup Contents of nav setup menuNavigation data source GPS receiver setup GPS setup menu Contents of GPS setup menuCon’t on next Contents of GPS setup menu con’t from previous Status TD setup menu TD display setupDisplaying Loran C TDs Loran GRI & station pair windowDecca chain and station pair window Displaying Decca TDsNav Data Display Setup Nav data setup screenNav data setup window Sounder Setup System setupOn next TVG Sounder system setup menu description con’t from previousSensor setup Sensor setup menuSensor setup menu settings Default basic ranges Sounder range setup menuSounding range, zoom range, bottom lock range Zoom range and bottom-lock rangesSounder function key options Sounder function key menuSounder function keys Memory Card Operations Formatting memory cardsSave data menu Save data menu Saving data to a memory cardMemory card messages Memory card messagesLoad data menu Playing back data from a memory cardUploading, Downloading Data Setting communication software on the PCUploading or downloading data Upload and download menusWaypoint data format Baud rate windowWaypoint data format Characters available for commentRoute data menu Route comment data formatEnd of sentence Loading Waypoint Data from Yeoman Receive data menu Receiving Data Via Network EquipmentHost name window Marks & lines windowSelect sentence menu Outputting Data Through the NetworkPreventive Maintenance Replacement of BatteryMaintenance program Trackball Maintenance Replacement of FuseGeneral troubleshooting Simple TroubleshootingRadar troubleshooting RadarPlotter Plotter troubleshootingSounder Sounder troubleshootingDiagnostics Memory I/O testMemory I/O Test menu Display unit test results Display unit testGPS sensor test Requires GPS Receiver GP-310B GPS receiver test resultsNetwork sounder test Requires Network Sounder ETR-6/10N Network sounder test resultsARP test results Test pattern sequence Test patternScreen for testing keyboard, remote controller Keyboard, remote controller testGPS status display GPS Status DisplayClearing Memories Memory clear menuWindows for clearing memory Error messages Error MessagesMenu key Menu OverviewAppendix System Port Appendix Plotter Chart Details MAP Soft KEY 1, Track ON/OFF Soft KEY 2, Edit MK/LINE Temperature Graph ON, OFF SPD Sensing PIC ADV ON, OFF Radar Alarms Alarm keyPlotter Alarms Sounder AlarmsGeodetic Chart List World Time Chart V E IconsModel 1833C/1933C/1943C Specifications of Marine RadarMODEL1943C Ggarmcrmagll Coating Color Specifications of Video Plotter GD-1900C IPX5 Index-1 IndexIndex Index-2Messages Index-3Index-4 Presentation modeTrackball Index-5
Related manuals
Manual 100 pages 8.64 Kb

1833C, 1933C, 1943C specifications

Furuno is a well-respected name in marine electronics, renowned for producing high-quality navigation and fish-finding equipment. Among their product line, the Furuno 1943C, 1953C, 1933C, GD-1900C, and 1833C stand out as reliable radar systems, providing exceptional performance and advanced features for both commercial and recreational vessels.

The Furuno 1943C is a powerful 12 kW radar system, boasting a 10.4-inch monochrome display with a user-friendly interface. It is equipped with digital signal processing (DSP) technology that enhances target detection and resolution. The 1943C offers superior target tracking capabilities, even in challenging weather conditions. Its patented Auto Gain Control ensures that small targets are not lost in clutter, making it a favorite among serious navigators.

Moving on to the Furuno 1953C, this model has an impressive 12 kW output and features a high-resolution 15-inch color display. It integrates advanced features such as Automatic Radar Plotting Aid (ARPA) for tracking multiple targets simultaneously, increasing situational awareness and safety on the water. Additionally, the 1953C offers a range of presentation modes, allowing users to customize the display to their specific needs.

The Furuno 1933C is a compact yet efficient radar solution with a 6 kW output and a 10.4-inch monochrome display. This system is highly regarded for its reliable performance and ease of use. Its user-friendly interface makes navigation simple, while features such as Target Analyzer and Echo Trails aid in identifying potential hazards, ensuring safe passage through busy waterways.

The Furuno GD-1900C combines chartplotting and radar in a single unit. With a 10.4-inch color display, it provides clear visuals of radar data as well as navigation charts. The GD-1900C supports various chart formats, including C-MAP and Navionics, allowing boaters to access detailed navigational information. This system is especially useful for those who need both radar and chartplotting capabilities in a space-saving design.

Lastly, the Furuno 1833C is a versatile radar system with a 4 kW output and a 7-inch color display, catering to smaller vessels. It features Furuno's advanced technology, such as a built-in GPS receiver and the ability to overlay radar data on electronic charts. This model is ideal for recreational boaters seeking an affordable yet feature-rich radar solution.

In summary, Furuno’s range of radar systems, including the 1943C, 1953C, 1933C, GD-1900C, and 1833C, demonstrates the brand’s commitment to quality and innovation in marine technology. Each unit incorporates advanced features tailored to meet the diverse needs of boaters, ensuring safe and efficient navigation on the water.
Top Page Image Contents