Furuno 1942 MARK-2 manual Other Menu Description

Page 27

3.10 OTHER MENU Description

The table below summarizes the OTHER menu.

 

 

Table 3-2 OTHER MENU Description

 

 

 

 

 

 

Item

 

Description

 

 

 

1.

Panel Dimmer

Selects level of panel backlight.

 

 

 

2.

Mark Brill

Selects brilliance of VRM, EBL, cursor, guard zone and WP marker.

 

 

 

3.

HD Mark

Selects brilliance of heading marker.

 

 

 

4.

Characters*

Selects brilliance of characters.

 

 

 

5.

Trail Tone

Selects brilliance of echo trails.

 

 

 

6.

Int Reject

Selects level of interference rejection.

 

 

 

7.

Pulselength

Selects pulselength for 1.5 and 3 mile ranges.

 

 

 

8.

Noise Reject

Selects “On” to reject noise.

 

 

 

9.

Trail Time

Selects the echo trail time.

 

 

 

10.

Tune

Selects automatic or manual tuning.

 

 

To tune manually;

 

 

1. Select “Manu” by the omnipad.

 

 

2. Press the [ENTER] key to enable manual tuning.

 

 

3. While pressing and holding down the [GAIN] control, operate the

 

 

 

omnipad to obtain best tuning condition, observing the tuning indicator

 

 

 

bar (1.0~11.9V).

 

 

4. Press the [ENTER] key.

 

 

“MANUAL” appears at the top right-hand corner when manual tuning is in

 

 

effect.

 

 

 

11.

Disp Data

Select the down sourse to display.

 

 

Selects data to display; Nav, ARP, or All (both Nav and ARP).

 

 

 

12.

WPT Mark

Selects “On” to display the waypoint marker.

 

 

 

13.

EBL Ref

Selects EBL reference for relative or true.

 

 

 

14.

VRM Unit

Selects distance unit of VRM and cursor for nm, km or sm.

 

 

 

15.

Watchman

Turns watchman on (set rest period) or off.

 

 

 

16.

STBY Disp

Select the display to use at stand-by; display “STBY” or navigation data, or

 

 

go into the economy mode.

 

 

 

17.

Guard Mode

Select condition which triggers guard alarm; targets entering guard zone

 

 

(In), target exiting guard zone (out).

 

 

 

18.

Own Position

Select position display format; L/L on Loarn TD.

 

 

 

19.

Cursor Posi

Display the cursor data in range/bearing or lat/long.

 

 

 

20.

Alm Sense LV

Select minimam echo strength which triggers guard alarm.

 

 

 

21.

Dead Sector

Select “On” to display the dead sector.

 

 

 

22.

Range

Select ranges to use.

 

 

 

23.

Self Test

Test keys, ROM and RAM; checks antenna rotation speed, and displays

 

 

program no.

 

 

 

24.

Installation Setup

Displays to the installation setup menu.

 

 

 

 

 

*Note: Level 1 and 2 are same brilliance while the menu is displayed. The brilliance changes after the menu is erased.

3-7

Image 27
Contents Marine Radar Page Nil Worst case 1.20 m Stay away from transmitting scannerRadiator Distance to Worst case 1.70 mKeep heater away from equipment Do not open the equipmentDo not disassemble or modify the equipment Use the proper fuseCompliance with R&TTE Directive 1999/5/EC Foreword FeaturesTable of Contents Menu KEY Menu TreeTable of Contents by INDICATION, Marker System Configuration Scanner UnitDisplay Unit How Radar Determines Bearing What is Radar?Principle of Operation How Radar Determines RangeHow radar works Control Description Basic OperationTransmitting Economy modeTurning the Radar On/Off Stand-bySelecting the Range Adjusting Picture BrillianceAdjusting Receiver Sensitivity Adjusting the A/C SEA Control Reducing sea clutterAdjusting A/C Rain Adjusting the A/C Rain Control Reducing rain clutterAdjusting the A/C SEA control Tip for adjusting the A/C SEAMeasuring range by cursor Measuring the RangeErasing the Heading Marker, North Marker Measuring range by range ringsMeasuring the Bearing Using the Offset EBLCancelling offcentered picture Offcentering the PictureMeasuring range and bearing between two targets Zoom Cancelling zoomHead up Selecting the Presentation ModeMenu Operation Basic Menu OperationMagnifying Long Range Echoes echo stretch Echo TrailContinuous trail Cancelling echo trailSuppressing Radar Interference Fixed time trailSelection of guard zone type Guard AlarmSetting a guard zone Selecting PulsewidthHow watchman works Silencing the audible alarmCancelling the guard zone and guard alarm WatchmanTo turn navigation data on or off Cancelling watchmanDisplaying Navigation Data Turning on watchmanOther Menu Description Other Menu DescriptionOutputting Target Position Adjusting Brilliance of MarkersFunction Controls Suppressing NoiseFalse Echoes Multiple EchoesSide-lobe Echoes Blind and Shadow Sectors Indirect EchoesGeneral remarks on receiving Sart Sart Search and Rescue TransponderShowing Sart marks on the radar display Summary to detect Sart responseThis page is intentionally left blank Maintenance & Troubleshooting Preventive MaintenanceReplacing the Fuse But Then TroubleshootingSelf Test This page is intentionally left blank Display accuracy is affected by the following Operation of ARP-10 OptionKeys used for auto plotter Principal specificationsGeneral ARP-10 Menu OperationARP Menu Deactivating the auto plotterAutomatic acquisition Setting auto acquisition areaAcquiring Targets Manual acquisitionAll targets Displaying Target DataTerminating Tracking of Targets Individual targetsPast Position Display Mode and Length of VectorsTrue or relative vector vector mode CPA/TCPA alarmLost target alarm This page is intentionally left blank Specifications of Marine Radar Display Unit Dimensions and Mass IN-1 IndexPage Page Page 00080835401