MT-62HS — OPERATION AND SAFETY DECALS
P/N 920100240
CAUTION
ATTENZIONE
ATENÇAÕ
PRECAUCION
*Read operator’s manual carefully before use.
*Libre le manual attentivement avant utillsation.
*Bitte lesen Sie vor inbetriebnahme der Maschine de Bedienungsanleitung sogfältig durch.
*Prima dell’ uso leggere attentamente il manuale.
*Lee com atenÇão o manual de instruÇões antes de usar.
*Leer detenidamente el mamual de instrucciones antes de usar la maquina.
P/N
| Oil |
| öl |
| I’ huile |
| SAE30 |
7~9 cc |
P/N 920209610
5 MM (3/16”)
PROPER SPONGE INSTALLATION
NPA 398 J
P/N 920203980
P/N 920209100
CLEANING ELEMENT:
Remove the element from the
Apply SAE30 motor oil with 7~9 cc, and squeeze out excess oil before
P/N
NOTICE
CLEAN THE ELEMENT WITH KEROSENE WHEN DIRTY. AFTER THE CLEANING, LUBRICATE IT MIXED OIL (KEROSENE 2~4: ENGINE OIL 1), SQUEEZE OUT THE OIL, AND REPLACE IT. AND CLEAN IT MORE
OFTEN WHEN OPERATING IN DUSTY CONDITIONS. |
P/N 920108310
DO NOT ALLOW WATER
TO ENTER FUEL AND OIL TANKS
P/N 920205990
To start, switch must be in the “ON” position
READ OWNER’S SERVICE MANUAL BEFORE OPERATING OR SERVICING THIS MACHINE.
ALWAYS KEEP UNAUTHORIZED, INEXPERIENCED, UNTRAINED PEOPLE AWAY FROM THIS MACHINE.
MAKE SURE ALL SAFETY DEVICES ARE OPERATIONAL BEFORE THIS MACHINE IS STARTED. MAKE SURE ENGINE IS TURNED OFF AND SPARK PLUG WIRE DISCONNECTED BEFORE SERVICING THE MACHINE OR COMING IN CONTACT WITH ANY MOVING PART. IF EQUIPMENT IS POWERED BY AN ELECTRIC MOTOR DISCONNECT ELECTRICAL PLUG.
SAE 10W-30
Motor Oil
P/N 920201950
NPA 293
P/N 920202930
When you stop the engine, be sure to close the fuel cock
P/N 920203990
NEVER LEAVE MACHINE UNATTENDED WHEN OPERATING. ALWAYS STOP ENGINE AND ALLOW ENGINE TO COOL BEFORE ADDING FUEL OR OIL.
P/N 920203290
NAMEPLATE
3800 ~ 4000 RPM | CONTACT MULTIQUIP |
P/N 920209840 | SERVICE DEPT. |
|
CAUTION
| 1. | Check that all bolts are tight. | |
| 2. | Before operation, check oil level at the sight gauge located | |
|
| on the operator’s side of the oil tank. Fill the oil tank to the | |
|
| “H” level using only outboard | |
P/N 920205810 | 3. | Fill the fuel tank. Use only regular unleaded gasoline. | |
4. To start the engine: Turn the ignition switch to the “on” | |||
| |||
|
| position. Open the | |
|
| Close the choke lever located on the carburetor and pull | |
|
| starter rope. When engine starts, open choke fully. | |
| 5. | Should the engine become difficult to start, open the drain | |
NPA-581 J
cock located on the lower side of the crankcase and discharge any excess fuel by cranking the engine 2 or 3 times.
6.Allow the engine to warm up for 4 to 5 minutes before operation.
7.To begin operation, move the throttle lever quickly from the “start” to the “run” or “on” position.
8.Remember to close the engine
9.When operation is complete, stop the engine by turning the ignition switch to the “off” position.
10.Note: Transport the machine with the
PAGE 10 —