Hobie 60 manual Vent Caps, Forward Crossbar Installation, Rear Crossbar Installation, Seat Bottom

Page 5

STEP 2- Vent Caps

Installing vent caps (2) as supplied creates a water and air tight seal. Screw caps onto threaded holes on top of pontoons.

Caps can be installed to self vent for altitude and temperature changes. To self vent, remove the clear plastic cone inside each cap by prying out with a small screwdriver. The cap will not completely seal and venting will take place as long as the cap is not over tightened. The plastic cones may be reinserted. Temperature and air pressure changes may cause contraction of the air inside the pontoons, possibly resulting in dents in the pontoons. Pontoons may become hard as air pressure increases inside. In either case, these conditions do not affect the strength or integrity of the boat. Loosen and tighten caps periodically to equalize the air pressure.

STEP 3- Forward Crossbar Installation

Insert one crossbar (Item 3) into forward molded opening of either pontoon, located by pointed end. Depress snap button and continue sliding crossbar through. As the crossbar enters the outside molded opening the snap button will pop into the first snap button hole. Do not insert crossbar into second pontoon at this time.

NOTE: IF YOU HAVE PURCHASED THE ROWING SYSTEM UPGRADE KIT, IT WOULD BE A GOOD TIME TO LOOK OVER THOSE INSTRUCTIONS NOW. THIS WILL HELP SAVE TIME BECAUSE THERE ARE STEPS FOR THE ROWING KIT THAT SHOULD BE DONE TO PREVENT YOU FROM HAVING TO PULL THE BOAT APART AGAIN.

STEP 4- Rear Crossbar Installation

Insert remaining crossbar (Item 3) into other molded opening of the same pontoon just far enough to expose the crossbar in trough. Locate one 6” webbing loop with a female buckle. Holding loop by the buckle, place loop in trough and slide crossbar through loop. Depress snap button and slide crossbar until snap button pops into place.

STEP 5- Seat Bottom

Locate mesh seat bottom (Item 8). The blue foam wedge inserted in the seat sleeve has a black X on one side. With the X facing down, and Velcro edges facing up, slide the seat over the rear crossbar by inserting the crossbar into the seat sleeve between the thick edge of the foam wedge and the mesh. The thick edge of the foam wedge is cut in the shape of a half circle to ensure a snug fit.

STEP 6- Final Framing

Trough

Part 7b 6” Loop Placement

Insert exposed ends of crossbars into molded openings in second pontoon just far enough to expose crossbar in trough. Place second 6” webbing loop in trough and slide crossbar through loop. Depress snap buttons and slide crossbars until snap buttons pop into place.

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Float CAT Hobie Float CAT Index Pontoon Placement Hobie Float Cat AssemblyRear Crossbar Installation Forward Crossbar InstallationVent Caps Seat BottomSafety Tether Seat Adjustment SystemSeat Bottom Lacing Seat Back PreparationStuck Snap Button Hull BagSnap Button Suggested Additional Equipment Safety PrecautionsFishing Techniques Entering Your Float CatManeuvering With Fins Do’s & Don’ts Maneuvering With OarsPage Warranty

60 specifications

The Hobie 60, a remarkable advancement in sailing technology, represents the epitome of performance and versatility in the world of catamarans. Designed with both casual sailors and competitive racers in mind, the Hobie 60 combines innovative engineering with the rich heritage of the Hobie brand, known for producing high-quality watercraft.

One of the standout features of the Hobie 60 is its impressive size. With a length of 60 feet, it offers ample space for both relaxation and performance sailing. Its generous beam ensures stability, allowing it to glide effortlessly over waves, making it an ideal choice for those seeking exhilarating sailing experiences. The spacious deck layout promotes comfort, enabling crew members to move around freely while enjoying the open waters.

Performance is at the heart of the Hobie 60, equipped with a powerful rig that optimizes sail area and enhances speed. The advanced sail design incorporates modern materials that are lightweight yet durable, allowing the vessel to achieve impressive velocities in various wind conditions. Additionally, the Hobie 60 features a state-of-the-art rigging system that allows for quick adjustments, ensuring effortless handling, even for novice sailors.

Technologically, the Hobie 60 showcases an advanced hull design that reduces drag and enhances buoyancy. The catamaran's dual hulls, crafted from high-quality fiberglass or composite materials, provide not only strength but also agility, enabling sharp turns and quick accelerations. The hulls are designed to cut through the water efficiently, delivering a smooth sailing experience while maintaining stability in choppy conditions.

Another notable characteristic of the Hobie 60 is its user-friendly design. The boat is equipped with intuitive controls and ergonomic seating, making it accessible for sailors of all skill levels. The large cockpit area promotes social interactions, making it perfect for gatherings and celebrations on the water. Moreover, the vessel's storage solutions ensure that all essential gear can be easily stowed, keeping the deck clutter-free.

In conclusion, the Hobie 60 is a remarkable sailing vessel that blends performance, comfort, and cutting-edge technology. With its impressive dimensions, innovative design, and user-friendly features, it appeals to a broad range of sailing enthusiasts. Whether embarking on a leisurely cruise or competing in races, the Hobie 60 stands out as a symbol of excellence in the world of sailing.
Top Page Image Contents