Baja Marine 20 Care & Refinishing, Paint Cleaning Agents & Other Substances, Stains & Scratches

Page 78

Section 9 • Care & Refinishing

Your new boat has been designed to provide you with years of enjoyment and satisfaction. In order to maintain the factory new appearance of your boat, we recommend the use of Yacht Brightproducts designed specifically for pleasure boats. Following proper fiberglass maintenance guidelines will help maintain your boat’s performance, value, and enjoyment.

1.Paint Cleaning Agents & Other Substances

Wash the gelcoat and fiberglass regularly with clean, fresh water. Wax gelcoated surfaces to maintain the luster. In northern climates, a waxing at the start and end of the boating season may suffice. In southern climates, an application of wax every three months will be required for adequate protection.

REFER TO THE Yacht Bright™ PAMPHLET IN YOUR OWNER’S MANUAL PACKET FOR INSTRUCTIONS AND WARRANTY INFORMATION.

3.Stains & Scratches

!WARNING

EXPLOSION/FIRE HAZARD

Care and refinishing materials may contain ingredients that are flammable or explosive. Do not use such materials in the bilge

Shut off electrical power and ventilate when using such materials anywhere on the boat or in the cabin.

Do not create sparks or use lighted materials.

!WARNING

Gelcoat surfaces are slippery when wet.

Always wear non-slip footwear securely fastened to your feet and hold on to rails or the boat structure.

!WARNING

Waxed surfaces are slippery.

Do not wax areas that are usually walked on.

Do not use products containing chlorine, phosphates, perfumes and non-degradable ingredients. Consult your marine dealer regarding environmental regulations before painting the hull. Fumes can last for hours, and chemical ingredients can harm people, property and the environment. Common household cleaning agents may cause hazardous reactions. Read and understand directions on all paint, cleaning and polishing materials before using.

2.Fiberglass & Gelcoat

The fiberglass hull, deck and some interior parts consist of a molded shell and exterior gelcoat. The gelcoat is the outer surface, often colored, that presents the shiny smooth appearance associated with fiberglass products. This gelcoat surface is painted or taped in some areas for styling purposes.

Although gelcoat and painted surfaces are resistant to deep stains, a need for cleaning will occasionally arise. But, the use of some common cleaning agents will permanently discolor or otherwise damage the finish on your boat.

Do not use abrasive porcelain-cleaning powders. These are too abrasive and contain chlorine and ammonia, either of which will permanently discolor gelcoat and paint.

Never use nail polish remover (acetone) or any ketone solvents.

Use diluted household detergents to remove surface soil and stains. Before using a given brand, check to make sure it contains no chlorine or ammonia.

Isopropyl alcohol can be used to remove difficult stains. But it must be promptly washed off with mild detergent and water.

20 Outlaw®

9.1

 

Image 78
Contents Baja Marine OutlawFor information call 1-865-971-6270 or fax Welcome This page intentionally left blank Introduction HIN Number Hull Identification Number HINAbout Your Express Limited Warranty Iii Ignition Protection Breakers and/or Fuses Speed changes you. TM Safety Safety LabelsLegally Mandated Minimum Required Equipment Fire Extinguishing SystemCarbon Monoxide Carbon Monoxide Monitor Lifesaving Equipment Additional Recommended Equipment for Safe Operation Impaired OperationPower Capacity Load CapacityPropellers Stability Maintain ControlChart Your Course WeatherGeneral Considerations Water Sports SwimmingSkiing Emergency Situations GeneralFire Medical EmergencyWater Rescue Flooding, Swamping and CapsizingGrounding Safety HotlinesCollisions and Leaking Propulsion, Control or Steering FailureInternational Requirements Environmental ConsiderationsFuel and Oil Spillage Waste Disposal Wake/WashExcessive Noise Nautical Terms Key to Symbols on Controls & Prints Only w/ fire port This Page Intentionally Left Blank General Boat Arrangement Docking /Lifting /Trailering Passenger Locations204 Basic Boat Dimensions and Clearances Metric Propulsion SystemGeneral Deck Layout Power Trim Unit and Gauge Description of Major ControlsGear Shift and Throttle Control Trailer Switch Trim TabsImportant Gauges Ignition Shutdown SwitchEngine Alarm System Tachometer and Hour MeterOil Pressure, Water Temperature, Voltmeter and Fuel Gauges Navigation and Anchor LightsUsing Your Boat Pre-Launch, Launch and Post- Launch ChecklistTrailer Launching and Loading Fueling the BoatBoarding Personal Flotation DevicesPassenger Instruction and Location Starting the EngineShifting to Drive the Boat Stopping the EngineSteering Systems Hydraulic SteeringPower Steering Power Steering SystemFuel & Oil Spillage Bilge & Underwater GearBilge Drain PlugBilge Blowers Maintenance and ServiceEngines and Stern Drive Vibration and CausesPropeller Removal and Installation Impact to Stern DriveGear case Fuel System Fuel SystemAnti-Siphon Valve Inboard/Outboard Engine Only Fueling Precautions Before and During Fueling ChecklistStatic Electricity and the Fuel System After Fueling Checklist This page intentionally left blank Direct Current DC Electrical SystemsElectrical Systems BatteriesElectrolytic Corrosion & Zinc Anodes Breakers and/or FusesFuse Panel Marine Electronic Cathodic Anti-corrosion System Mercathode Drive Pump Drive Pump w/ K-Plane Trim Tabs Ignition Switch DC Wiring Information FIG Switch Panel Wiring Information FIG Options & Accessories Options & Accessories LocationsAutomatic Fire Extinguisher Horn Canvas Care and MaintenanceCanvas Swim Platform w/ Ladder OptionalDepth Finder Optional Exhaust Systems Stereo SystemRequired Inspection, Service Maintenance Summary Guide for Inspection, Service and MaintenanceInterval Summary Guide For Inspection, Service and Maintenance IntervalUseful Service Information Inspection, Service and Maintenance Protocol Bilge AreaTopside and Supplies Winterization Checklist for Boats Stored on LandBatteryies Boat StorageFuel System Fitting Out After StorageFuel Systems MiscellaneousPower Steering System Maintenance Security ConsiderationsQuick Reference Checklist Boarding the Boat GeneralBoat Systems Starting the Engine Quick Reference Checklist cont’d Departing General Returning to Port GeneralQuick Reference Checklist cont’d Securing the BoatIf the Engine Does Not Start After Market Equipment Checklist Maintenance Log Maintenance Log Cont’d Stains & Scratches Paint Cleaning Agents & Other SubstancesCare & Refinishing Fiberglass & GelcoatAcrylic Plastic Sheeting Plastic Glass Permanently Moored or Docked BoatsTopside Areas Canvas and Clear VinylExterior Upholstery Fabric Interior Upholstery FabricThis Page Intentionally Left Blank Index Index Outlaw