Pioneer CT-W803RS Single Recording, Adjusting the Recording Level, Recording Using Microphone

Page 14

I RECORDING

SINGLE RECORDING

 

I CT-W803RS/CT-W703RS:

both Deck I and II

l CT-W603RS: Deck II only

 

42

 

1.Load a tape for recording in DECK II (or I).

2.If you use AUTO BLE tuning, press the BLE button of DECK II (or I).

The II (or I) indicator will flash in the AUTO BLE display for about 30 seconds, after which it will light steadily (see page 15).

3.Set the DOLBY NR ON/OFF switch and set the DOLBY NR switch.

4.Set the REV MODE switch.

•To record on one side only, set the switch to the _ posi-

tion. To record on both sides, set the switch to the=--_ posi- tion.

5.Press the recording (e) button of DECK II (or I).

6.Prepare the audio source from which you wish to re- cord. Turn on the stereo amplifier and prepare it for playback of the desired audio source.

7.Adjust the recording level. For details, see "ADJUST-

ING THE RECORDING LEVEL" below.

8.Press the playback (1_ or _1) buttpn or the pause (11) button of DECK II (or I) to begin recording.

•When recording on both sides, press the • button. If the •

button is pressed, recording will stop after only one side is recorded.

To stop recording temporarily

Press the pause (ll) button.

•To resume recording, either press the pause (II) button again, or press the playback (1_ or <1) button.

TO stop recording

Press the stop ( • ) button.

Erasure prevention tabs

The recording ( • ) button does not work when the erasure preven- tion tabs of the loaded cassette tape have been broken off (See page 5). Do not press the recording ( • ) button with unreasona- ble force. When recording on both sides, make sure that both tabs are intact.

ADJUSTING THE RECORDING LEVEL

The adjustment of the recording level is the most important factor

in achieving good recording results. A high level provides a good

signal-to-noise ratio and dynamic range, but an excessively high level distorts the sound. If the level is set too low for fear of sound

distortion, irritating tape hiss will mar the recording. The charac-

teristics of tapes differ depending on the manufacturer and the type of tape. Set the REC LEVEL control so that the level meter's "-3dB" indicator lights steadily most of the time. No harm will be

done if the "0 dB" indicator lights momentarily at peaks. When

14

<RRB1143>

En

recording without Dolby NR, set the REC LEVEL control so that the "-3 dB" indicator lights, and the "0 dB" indicator lights occasion- ally at peaks.

NOTES:

•The optimal recording level may differ somewhat depending on the audio source and type of tape used. In order to obtain the best possible results, set the recording level after actual testing. Listen to your recordings, and adjust the level as necessary.

•The level meter may react differently during recording and playback of the same tape. This is due to differences in tape sensitivity, and creates no problem.

•ff Deck I and II are loaded with tapes, relay recording will per- formed from both the forward and the reverse sides of the tape in the Deck I, then both sides of the tape in Deck II. Be sure to check the position of the REV MODE switch before recording when you loaded tapes in both the Deck I and I/.

RECORDING USING MICROPHONE

(CT-W803RS/CT-W703RS only)

1.Connect the plug of the microphone to the MIC jack.

2.Follow the procedure for RECORDING given above.

•To adjust mic recording level (step 7), use the mic level con- trol (LEVEL) instead of the REC LEVEL control.

•Set the REC LEVEL control to its minimum position when

recording with a microphone only. <Mixing recording>

Turn the REC LEVEL control up gradually after playing back music source during microphone recording.

Use both the REC LEVEL control and the MIC LEVEL control to

adjust mixing level balance between microphone sound level and line source sound level.

NO TES:

•The MIC LEVEL control is only effective when a microphone is connected to the M/C jack.

•Be sure to disconnect the microphone plug from the MlCjack when not using the microphone for recording.

•Use a commercially available microphone when recording.

RECORDING MUTE

Use this function to create the 4.5-second blanks needed for proper operation of the music search function.

•Press the recording mute ( O ) button during recording and the deck will create a blank space by recording a section which con- tains no signal for approximately four seconds. The deck will then enter recording standby mode.

•To create a blank which is more than four seconds long, hold the button down for the desired length of time. When the but- ton is released, the deck will enter recording standby mode.

•To resume recording, press the pause (I) button or the play- back (1_ or 4) button.

Page 13 Page 15
Image 14
Page 13 Page 15
Contents For Canadian model Important NoticeFor U.S. and Canadian models Safety Instructions For USE in the United KingdomWe Want You Listening For a Lifetime Installation ContentsAre the accidental erasure prevention tabs intact? Check Cassette Before USETips on Cassette Tapes Automatictape SelectorfunctionConnecting the Power Cord Connecting Recording Playback CordsPioneer System Remote Control Lfront Panel Facilities Double Decks system remote control Except for CT-W803RS Reverse Mode Switch REV ModeOne way mode z position Auto BLEB/C-type Dolby NR Systems Function DisplayDolby NR & Dolby HX PRO Dolby HX PRO Headroom Extension SystemFor both Deck Except for Deck I of CT-W603RS Tape Transportation Mode IndicatorsFor both Deck I TWO Modes CounterPower button Remote Control OperationRemote Control Operable Range CT-W803RS onlyCT-W603RS Single PlaybackEither Deck I or Deck Relay PlaybackPlayback Playback Sequence with REV Mode Switch SettingMusic Search Single Recording Adjusting the Recording LevelRecording Using Microphone Recording Mute23 1 Auto BLE TuningWhen tuning Deck II or RecordingParallel Recording CT-W803RS only J 2103 Relay Recording Sequence with Reverse Mode Switch SettingAdjusting the Recording Level ModeAbout Recording When the compact disc finishes playingCDeDECK Synchro Recording To stop recording temporarilyHigh To stop copyingNormal Cassette Door TroubleshootingPower PlaybackNR ON/OFF TroubleshootingPOWER-CORD Caution OthersMiscellaneous AccessoriesSubfunctions MICRRB1 lqJ TIME/COUNT AboutMode Pioneer Electronic Europe N.V

CT-W603RS, CT-W803RS specifications

The Pioneer CT-W803RS and CT-W603RS cassette decks are celebrated models in the world of audio equipment, renowned for their exceptional sound quality and robust features tailored for audio enthusiasts. Both models represent Pioneer's commitment to high-fidelity sound reproduction, blending cutting-edge technology with user-friendly interfaces.

The CT-W803RS, the flagship of the duo, boasts advanced dual cassette recording capabilities, allowing users to effortlessly transfer music from one cassette to another while maintaining high audio fidelity. One of its standout features is the Double-Dolby system, which includes Dolby B and C noise reduction, significantly minimizing background noise and enhancing the overall listening experience. This model is also equipped with a high-quality quartz PLL (Phase-Locked Loop) digital control system, ensuring precise tape speed and playback accuracy.

Another significant feature of the CT-W803RS is its automatic tape selection function, which detects the type of cassette inserted—normal, chrome, or metal—and adjusts the playback settings accordingly. This automatic optimization ensures that listeners experience the best possible sound, regardless of the tape's formulation. The deck includes a built-in timer that enables users to record from various sources, making it ideal for preserving precious audio moments.

The CT-W603RS, while a step down from the 803 model, does not compromise on quality. It features similar noise reduction technology and automatic tape detection, delivering excellent sound fidelity and user comfort. The 603 model is designed with a compact form factor, making it an attractive choice for those who require high performance without the bulk.

Both models come with programmable features, allowing users to create custom playlists for audio enjoyment. They also support standard features like auto-reverse capability, making it easy to listen to both sides of a tape without interruptions.

In terms of connectivity, both cassette decks offer line-level inputs and outputs, ensuring compatibility with various audio systems. The design aesthetic of both models reflects Pioneer's quality with durable construction and sleek, intuitive controls.

In summary, the Pioneer CT-W803RS and CT-W603RS cassette decks exemplify the pinnacle of analog audio technology. With their advanced recording features, noise reduction systems, and automatic tape detection, they cater to a wide audience from casual listeners to serious audiophiles, making them worthy components in any audio setup.
Top Page Image Contents