Pioneer CT-W803RS, CT-W603RS Reverse Mode Switch REV Mode, One way mode z position, Auto BLE

Page 8

FRONT PANEL FACILITIES

REVERSE MODE SWITCH (REV MODE)

There are three settings:

One way mode z position

When the switch is set to this position, playback or recording is

performed on one side of the tape only. When the tape reaches

the end of the side, it stops automatically (auto stop function).

Two way mode _-_position

When the switch is set to this position, playback or recording can

be performed on both sides of the tape. When the tape reaches

the end of the first (forward) side, its direction is automatically

reversed, and playback or recording continues on the other

(reverse) side. When it reaches the end of the reverse side, the

tape stops automatically (auto stop function). If playback or re- cording is started from the reverse side, the tape will stop when it reaches the end of that side.

Repeat modec--=-_ position (RELAY/SKIP)

When the switch is set to this position for playback, both sides of

the tape are played back repeatedly until the stop (i) button is

pressed, or until the tape has been played completely 15 times (16 sides). If Deck I and II are loaded with tapes, each tape will be played 15 times using relay playback and then both decks will stop

automatically. If the pause button is pressed to pause the tape, and then playback is restarted, the repeat mode starts over from

the beginning, and will play the tape 15 times (16 sides).

When the switch is set to this position for recording, both sides are recorded and then the tape stops, as described above for the two way mode.

If Deck I and II are loaded with tapes, relay recording is used when the recording starts with Deck L

OPERATION OF DECK I WITH A REMOTE CONTROL UNIT NOT DESIGNED FOR

DOUBLE DECKS (system remote control) (Except for CT-W803RS)

Selecting DECK I

In order to operate DECK I with the remote control unit, adjust the unit as follows: With the power off, press and hold the stop (i) button of DECK I, and turn the power on. Continue to hold the stop

(11)button for approximately five seconds. DECK I can now be operated using the remote control unit, but DECK I! cannot.

Switching to DECK II

To restore remote control operation to DECK II, press the stop (e) button of DECK II while DECK II is in stop mode. DECK II can now be operated using the remote control unit. Remote control oper-

ation can be switched back and forth between decks by pressing the stop button of the desired DECK while it is in stop mode.

NO TE:

If a power failure or a sudden change in the power supply (caused

by lightning, etc.) occurs, the unit is reset to its original state. Only

DECK II can be operated by remote control To restore operation to

either deck, repeat the above procedure from the beginning.

8

<RRB1143>

En

I AUTO BLE

..... 1

With commercially available cassette tapes, sensitivity and fre- quency characteristics might differ slightly from one another, even though the same sound adjustment is set for them. To utilize tape characteristics to the maximum possible and realize an ideal recording which reproduces the source exactly, optimum record- ing level (sensitivity) and equalizer values must be set accordingly for each tape. In many conventional tape decks, standard values are fixed for standard tapes, thus nullifying the subtle differences between individual tapes. Perfect tuning by ear through use of fine adjustment controllers for bias and sensitivity is difficult and requires a lot of effort. It is especially difficult with a 2-head deck where the recording sound cannot be monitored.

The AUTO BLE on this unit automatically adjusts bias, level and equalizer by using a microprocessor to set the optimum recording characteristics accordingly for each tape.

I FLEX (1If) SYSTEM

I

•FLEX System: Frequency Level Expander System

This system automatically compensates high and low fre- quency level balance above 1 kHz according to the 1/f curve during playback.

Generally, envelope line of sound energy distribution of Hi-Fi sounds corresponds statistically with the 1/f curve.

The 1If curve indicates that if the frequency doubles the level decreases by approx, half of the original frequency level.

•During playback, the FLEX system automatically compensates tapes with poor sound quality at high frequency levels of 1 kHz and over based on the appropriate auditory characteristics. The FLEX system is designed to improve high frequency repro- duction in the 10 kHz range be up to 12 dB, particularly in tapes with poor sound clarity and sound presence at high frequency levels. If the playback tape sound matches the 1/f curve, the FLEX system defeats compensation adjustment automatically.

•When you press the FLEX button to turn the FLEX system on and start playback, the 1/f indicator flash and compensation adjustment begins.

Compensation adjustment takes within approximately 3 sec- onds to complete, depending on the music source. The indica- tor change from a flashing to a steadily lit condition.

•When the FLEX system is engaged, each music selection is automatically adjusted during playback. System operation status is indicated by whether the 1/f indicator is lit.

Even when the FLEX system is turned on, the 1/f indicator is nullified automatically during all recording functions including: AUTO BLE tuning, CDeDECK synchro recording, and tape copy- ing.

NO TE:

•When a tape has been recorded at a high frequency level above the compensation level, the FLEX system operation is automati- cally defeated during playback.

Page 7 Page 9
Image 8
Page 7 Page 9
Contents For Canadian model Important NoticeFor U.S. and Canadian models Safety Instructions For USE in the United KingdomWe Want You Listening For a Lifetime Installation ContentsCheck Cassette Before USE Tips on Cassette TapesAre the accidental erasure prevention tabs intact? Automatictape SelectorfunctionConnecting the Power Cord Connecting Recording Playback CordsPioneer System Remote Control Lfront Panel Facilities Reverse Mode Switch REV Mode One way mode z positionDouble Decks system remote control Except for CT-W803RS Auto BLEFunction Display Dolby NR & Dolby HX PROB/C-type Dolby NR Systems Dolby HX PRO Headroom Extension SystemTape Transportation Mode Indicators For both Deck IFor both Deck Except for Deck I of CT-W603RS TWO Modes CounterRemote Control Operation Remote Control Operable RangePower button CT-W803RS onlySingle Playback Either Deck I or DeckCT-W603RS Relay PlaybackPlayback Playback Sequence with REV Mode Switch SettingMusic Search Adjusting the Recording Level Recording Using MicrophoneSingle Recording Recording MuteAuto BLE Tuning When tuning Deck II or23 1 RecordingRelay Recording Sequence with Reverse Mode Switch Setting Adjusting the Recording LevelParallel Recording CT-W803RS only J 2103 ModeWhen the compact disc finishes playing CDeDECK Synchro RecordingAbout Recording To stop recording temporarilyHigh To stop copyingNormal Troubleshooting PowerCassette Door PlaybackTroubleshooting POWER-CORD CautionNR ON/OFF OthersAccessories SubfunctionsMiscellaneous MICRRB1 lqJ About ModeTIME/COUNT Pioneer Electronic Europe N.V

CT-W603RS, CT-W803RS specifications

The Pioneer CT-W803RS and CT-W603RS cassette decks are celebrated models in the world of audio equipment, renowned for their exceptional sound quality and robust features tailored for audio enthusiasts. Both models represent Pioneer's commitment to high-fidelity sound reproduction, blending cutting-edge technology with user-friendly interfaces.

The CT-W803RS, the flagship of the duo, boasts advanced dual cassette recording capabilities, allowing users to effortlessly transfer music from one cassette to another while maintaining high audio fidelity. One of its standout features is the Double-Dolby system, which includes Dolby B and C noise reduction, significantly minimizing background noise and enhancing the overall listening experience. This model is also equipped with a high-quality quartz PLL (Phase-Locked Loop) digital control system, ensuring precise tape speed and playback accuracy.

Another significant feature of the CT-W803RS is its automatic tape selection function, which detects the type of cassette inserted—normal, chrome, or metal—and adjusts the playback settings accordingly. This automatic optimization ensures that listeners experience the best possible sound, regardless of the tape's formulation. The deck includes a built-in timer that enables users to record from various sources, making it ideal for preserving precious audio moments.

The CT-W603RS, while a step down from the 803 model, does not compromise on quality. It features similar noise reduction technology and automatic tape detection, delivering excellent sound fidelity and user comfort. The 603 model is designed with a compact form factor, making it an attractive choice for those who require high performance without the bulk.

Both models come with programmable features, allowing users to create custom playlists for audio enjoyment. They also support standard features like auto-reverse capability, making it easy to listen to both sides of a tape without interruptions.

In terms of connectivity, both cassette decks offer line-level inputs and outputs, ensuring compatibility with various audio systems. The design aesthetic of both models reflects Pioneer's quality with durable construction and sleek, intuitive controls.

In summary, the Pioneer CT-W803RS and CT-W603RS cassette decks exemplify the pinnacle of analog audio technology. With their advanced recording features, noise reduction systems, and automatic tape detection, they cater to a wide audience from casual listeners to serious audiophiles, making them worthy components in any audio setup.
Top Page Image Contents