Multiquip CV2a/2B, CV1A, CV3A/3B manual VIbRatoR motoR saFetY, EleCtRICal saFetY

Page 11

Safety Information

VIbRatoR motoR saFetY

dangeR

alWaYs wear rubber insulated gloves and boots when holding the fl exshaft during operation. The possibility of electrocution exists causing equipment damage and severe bodily harm even death!

dangeR

If applicable, periodically check insulation resistance as referenced in maintenance section. The possibility of electrocution exists causing equipment damage and severe bodily harm even death!

WaRnIng

neVeR attempt to run the core outside the casing assembly for any reason.

CautIon

do not overreach. Keep proper footing and balance at all times.

do not carry plugged-in motor with fi nger on the switch.

neVeR carry the motor by the cord. Use the carrying handle.

alWaYs check the vibrator motor for loosened hardware such as nuts and bolts before starting.

Keep the cord from heat, oil, and sharp objects.

do not overload the motor. It will do a better and safer job at the rate for which it was designed.

do not expose vibrator motor to rain.

do not use vibrator motor in damp or wet locations without proper electrical circuits.

alWaYs keep clear of rotating or moving parts while operating the vibrator motor.

neVeR leave the machine unattended while running..

alWaYs disconnect the motor from the power source when not in use, before servicing, and when changing fl exible shafting and vibrator heads.

Allow the vibrator motor to cool before servicing. Contact with hot components can

cause serious burns.

Before each use, alWaYs check the motor

to make certain that there are no damaged parts and that all parts function properly (such as switch, cord housing). If any damage or malfunctioning parts are found, have them repaired or replaced by an authorized service facility.

NOTICE

Secure forms. Make sure the form work is well made and braced to withstand the stresses made by vibration.

Keep vibrator motor clean for better and safer operation.

alWaYs store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

Use only factory-authorized replacement parts.

Store idle vibrator motor. When not in use, motor should be stored in a dry, safe storage area.

eleCtRICal saFetY

CautIon

Prevent body contact with grounded surfaces such as pipes, reinforcing bar, etc.

When applicable, use a protection wiring device, such as a Ground Fault Circuit Interrupter, for the protection of personnel.

Operate electric motor only at the specifi ed voltage indicated on the nameplate.

do not spray water onto electric motor.

do not yank the cord to disconnect it from the receptacle. Grasp the plug itself to disconnect it.

alWaYs make sure the ON/OFF switch on the electric motor is in the OFF position when not in use and before inserting the power plug into an AC receptacle.

cv sERIES vibrator motor • operation and parts manual — rev. #0 (04/30/13) — page 11

Image 11
Contents Models Silicosis Warning Silicosis/respiratory warningsPage CVS Series Vibrator Motor Table of ContentsChoose from three easy options Personal safety General power tool safety warningsWork area safety Electrical safetyGeneral power tool safety warnings Vibration Emissions Noise EmissionsSymbol Safety InformationSaFetY messages SaFetY sYmbolsGeneRal saFetY EleCtRICal saFetY VIbRatoR motoR saFetYRemoVe tHe gRoundIng pIn FRom tHe plug Power Cord/Cable safetyEnVIRonmental saFetY/deCommIssIonIng Drive Motors SpecificationsVibrator Motor Specifications Dimensions DimensionsVibration range General informationConsolidation Vibration timeExtension Cord Sizes AWG ExampleModel Shaft Head Max. Shaft Attaching Vibrating Head To flex-ShaftShaft Sizes Attaching flexshaft to drive motor Installing fsc shaft couplerOperation OperationFlexshaft lubrication 100 Hours MaintenanceBronze wear bushing replacement Vibrator head lubrication 300 Hours Cleaning Wire CoreVibrator Head Wear Diameter Vibrator head wear 300 HoursVibrator Head Oil Capacity Troubleshooting Flexshaft TroubleshootingTroubleshooting Drive Motor Possible Problem SolutionExplanation of Code in Remarks Column Page Decals Part Name QTY Remarks Vibrator motor housing assy END CAP, Rubber 16 1 Vibrator motor assyPart Name FReIgHt polICY Terms and Conditions of Sale PartsPage HERE’S HOW to GET Help

CV3A/3B, CV1A, CV2a/2B specifications

Multiquip has established a strong presence in the construction and equipment rental industries with its versatile range of products, including the CV2A/2B, CV1A, and CV3A/3B concrete vibrators. These models are designed to enhance the efficiency and quality of concrete placements, making them essential tools for contractors and construction professionals.

The CV2A and CV2B are two models that stand out due to their user-friendly design and powerful performance. Both models feature a robust 1.5 HP electric motor that delivers consistent vibration to ensure uniform consolidation of concrete. The CV2A model is equipped with a 10-foot shaft, while the CV2B provides a longer 12-foot shaft, making them suitable for a variety of applications, from small to large pours. The ergonomic handle and lightweight construction allow for easy maneuverability, reducing operator fatigue.

The CV1A, on the other hand, is a more compact option that excels in smaller job sites and tight spaces. It features a 1 HP motor and a 6-foot shaft, making it perfect for residential projects and delicate applications. Its simple, straightforward controls make it easy for operators to achieve optimal vibration levels without extensive training.

For larger-scale operations, the CV3A and CV3B vibrators deliver unparalleled performance, capable of handling substantial concrete loads with ease. Both the CV3A and CV3B feature powerful 2 HP motors and longer shaft lengths, with 10 feet for CV3A and 12 feet for CV3B. These models are designed for heavy-duty applications, making them ideal for commercial and industrial construction projects.

One of the standout features across all these models is their durable construction. Built with high-quality materials, they can withstand the rigors of daily use on construction sites. Additionally, the vibrators are designed with maintenance in mind, featuring accessible components that streamline upkeep and repairs.

Furthermore, Multiquip's focus on safety is evident in these models, which include protective features to prevent overheating and electrical overloads. This commitment to safety, combined with their powerful performance and innovative design, makes the Multiquip CV2A/2B, CV1A, and CV3A/3B concrete vibrators reliable choices for any concrete-related task, ensuring solid results and increased productivity on the job site.