Furuno CSH-83, CSH-84 manual Menu screen location and display mode, User Menu Hist DSP/GRPH

Page 42

2.Operate the arrow keys in sub panel 1 to select a menu. As you move through the menu, each item, initially shown as blue on gray, reverses to gray on blue to show selection. For example, select the HIST DSP/GRPH menu.

3.Press the MENU key to display menu selected.

USER MENU

HIST DSP/GRPH

Select item with dc[ \ keys and press MENU key. Press END key to close menu.

HIST Window DSP

AUDIO

PRT/STBD

H-Slice

Fish Histogram

ON

OFF

Figure 5-2 HIST DSP/GRPH menu

4.Operate the up and down arrow keys in sub panel 1 to select menu item, and the right and left arrow keys to select option.

5.Press the END key to close the menu. Press the key again to display picture.

Note: The HELP key provides menu operating information.

Menu screen location and display mode

Menu screen location depends on display mode as shown in the figure below.

Menu

Menu

Normal Mode

Combination Mode

Figure 5-3 Menu screen location and display mode

5-2

Image 42

Contents Color Scanning Sonar 00080806600 Safety Instructions Do not use the equipment for other than its intended purpose Table of Contents PORT/STARBOARD, Horizontal Slice Displays Self Tests This page is intentionally left blank Features ForewordWord to CSH-83/84 Owners System Configuration Standard OptionControl Layout on Display Unit and Remote Control Box Control DescriptionMain Panel Main panel control descriptionControl Function Sub Panel ENDSub Panel 2 data setting window Process SignalAGC 2AGCUP/TM AlarmSonar SonrbeamRemote Control Box + +Operational Overview Turning the Power On/OffAdjusting Screen Brilliance, Control Panel Backlighting Lowering the TransducerSelecting a Display Mode Display mode descriptionSetting the Tilt Angle Selecting a Display RangeSeabed echo and tilt angle How to discriminate fish echoes from the seabed Points to considerTilt angle for surface fish Tilt angle and sea surface reflectionsSuitable tilt angle Tilt angle and beam coverageAdjusting the Gain Measuring Range and Bearing to a TargetPage Fine Tuning the Picture How to adjust TVGEliminating Unwanted Feeble Echoes Page 2AGC data setting window SIGNAL, Signal Process AGC data setting window SIGNAL, SignalPulselength data setting window TVGTX,PL Suppressing Seabed TailData setting window TVGTX, Output Rejecting Sonar Interference and NoiseIdentifying noise source Changing Tx cycle data setting window Tvgtx CycleAdjusting Beamwidth Setting Noise limiter data setting window SignalMarks, Data and Display Mode Normal display modeMarks and Data Normal display mode w/text Echo sounder combination displayPermanently Displayed Marks and Data History displayErasable Marks and Data Mark/Data DescriptionBearing marker Mark Description Range R Auto Tilt Auto Scan Gain Brill TVG TVG DIM Page Menu Overview User Menu OperationMenu screen location and display mode User Menu Hist DSP/GRPHUser Menu Description Current VEC Save PictureTM DSP System Menu DescriptionFAR TVG Target LockBRG Readout Mark SizeMenu Description Data SET Menu Description Color CurveChange Color NET Sonde NET ShootPlan NET Plot CorrInit SET/TEST Menu Description NET REC DefaultsEcho Test Others Event KEYFunction Keys Programming the Function KeysFunction Key Fine Tuning Replaying a Function KeySaving Function Key Settings to a Memory Card Replaying Function Key Settings from a Memory CardThis page is intentionally left blank How to find fish school center Advanced Level OperationFinding Fish School Center Tracking a Fish School target lock Tracking a fish schoolChoosing target lock mode Target lock mark appearanceErasing target lock mark Tracking target lock mark Target lock and tilt angleSetting target lock conditions System Menu Target LockDescription of target lock items Detecting Fish Schools Aurally Fish Alarm How to set the fish alarm zoneHow to relocate fish schools Relocating Fish School for Easy ObservationComparing of Fish School Concentration Estimate marks and their dataHow to measure fish speed Measuring Fish School SpeedEvent Mark 10 Event marksEntering an event mark Erasing an event markTrue Motion Display 12 True motion displayPlotting Net Location Mark 13 Net location markObserving Net Behavior 14 Net behaviorTarget Slice Display No. Display Information ApplicationsThis page is intentionally left blank PORT/STARBOARD, Horizontal Slice Displays Port/Starboard displayHorizontal slice display Horizontal slice displayMemory Card Operations Initializing Memory CardsSaving the Picture Transferring Echo Data from Internal Memory to Memory CardHow net shooting data is saved Net shooting data contentsSaving Net Shooting Data Transferring net shooting data to memory cardDeleting Memory Card Contents Replaying Saved DataTurning marks on/off through the data setting window Turning MARKS, Data ON/OFFTurning marks on/off through the user menu 10-2 Interpreting the Display Seabed EchoesFish Schools Sea surface fishSea Surface Reflections WakeFalse Echo by Sidelobe Noise and InterferenceOvervoltage Warning Unretracted Transducer WarningHow to manually raise the transducer Self Tests Opening the Self Test MenuSelf Test Description Single testContinuous test Panel test Color testGray test SIO testInterface Unit CS-120A Self Test Interface unit CS-120A, cover opened13-6 Input Data Selection Selection of Data at Interface Unit CS-120ASetting Distances Between Net Sonde Transmitters How to set net sonde transmitter distancesMaintenance Display Unit MaintenanceHull Unit Maintenance Zinc block near the transducer must be replaced yearlyMenu Tree User MenuData SET Menu Init SET/TEST Menu System Menu Previous Page Specifications SP-1Display SP-2Hull Unit SP-3SP-4 Index 11-2IN-2