Furuno GP-1850DF installation manual Checking the Dgps installation, Inside of the cover

Page 45

GN gasket

Shield gaskets

Figure 4-10 Inside of the cover

Checking the DGPS installation

1.Press the [MENU] key.

2.Press the software key labeled "CONFIGURATION".

3.Press the software key labeled "SYSTEM MENU".

4.Press the software key labeled "SELF TEST".

5.Press the software key labeled "MEMORY•I/O TEST" to display the following message.

		TEST
	PROGRAM : OK	INTERNAL
	NO. 14518310XX	BATTERY : OK
	SRAM : OK	GPS
	SRAM : OK	RECEIVER : OK
		RECEIVER : OK
		NO. 48502060XX
	DRAM : OK	BEACON
		BEACON
		RECEIVER : OK
	PORT1 : OK*	NO. 0850182-0XX
	PORT2 : OK*	NO.
		RETURN

*: Special connections are required to check these port. Otherwise, "--" (bar) appears.

Figure 4-10 Memory, I/O Test Display

6.Confirm that "BEACON RECEIVER: OK" is displayed.

7.Press the soft key labeled "RETURN".

8.Press the [PLOT] key to return the plotter display.

4-7

Image 45

Contents

AP-1 Installation of Dgps Beacon ReceiverB . N o . I M E 4 3 9 5 0 J Safety Instructions for the Installer Safety InstructionsOptional equipment Standard supplyIii System Configuration Mounting considerations Installation of Display UnitMounting procedure Tabletop, overhead mountingFlush mounting Flush mounting of display unit Installation of Antenna UnitInstalling the inside-hull mount transducer Installation of TransducersRemarks on installation Necessary toolsCoating the transducer face with silicone sealant Attaching the transducerMODE/FREQ Auto Cruising Auto Fishing Manual Observing the pictureFinal preparation Installing the thru-hull mount transducer Transducer mounting locationTransducer outline drawings Acceptable transducer mounting locations Typical through-hull mount transducer installations15 Construction of fairing block Procedure for installing the thru-hull mount transducer16 Transom mount transducer mounting locations Installing the transom mount transducer17 Transom mount transducer, mounting flush with hull Transducer preparationMounting considerations Triducer 524ST-MSD, 525ST-MSDTransom mount water temperature sensor Installation of Sensors21 Thru-hull mount water temperature sensors 02MSB, T-03MSB Thru-hull mount water temperature sensor 02MSB, T-03MSBST-02PSB Power cable WiringAntenna unit Water temperature/speed sensorTransducer GroundCable extension Extending antenna cable lengthHow to attach the N-P-8DFB connector Nmea port Nmea SettingRTCM104EXTRN Dgps portRTCM104INTRN RTCM104OUTPUTInput/Output Sentences Output Data SentencesAntenna Height Baud Rate Setting GP-1850DF onlyBeacon Baud Rate Beacon Frequency Setting GP-1850DF onlyBeacon Frequency Auto Depth AdjustmentExternal Equipment Setup Option Speed SourceSpeed Source OWN Pddwhl GPS Speed Adjustment Temperature AdjustmentSpeed ADJ Temp Graph OFF Temp ADJ14 Display unit, top view Selecting the Echo Sounder Output Power15 Removing cover assembly 17 Inside of the cover Installation of Dgps Beacon Receiver for GP-1850F Procedure Disassembly Dismounting chassis assembly Installation of Dgps receiverInstallation of Dgps beacon receiver Wiring the Cable assembly Attaching chassis assembly 10 Inside of the cover Checking the Dgps installationAppendix Triducer 525ST-PWC/PWD AP-2 AP-3 Page Page Page Page 11 Connecting Dgps beacon receiver Connecting Dgps beacon receiverPage Page Page Page Page Page Page Page

Related manuals

Manual 110 pages 14.73 Kb