Line 6 Flextone Cab 212S user manual Channel Select, Manual Mode

Page 33

Flextone Manual Rev E; bookfile Page 33 Tuesday, September 8, 1998 10:31 AM

THATS USING YOUR FEET: USING THE FLOOR BOARD WITH THE FLEXTONE

display ( 22) will show you. To switch between your Preset and User Banks bring your foot around to step on both of the Bank Select switches at the same time and you’ll be transported instantly from one region of time-space to the other. Trippy, huh?

Channel Select

So, now that we’ve got this whole Bank thing down, let’s move onto the other four switches on the bottom row. These let you pick which of the four channels – A, B, C, or D – you want to use in the bank you’ve selected. Pick your Bank ( 21 ), hit one of the Channel Select switches ( 23), and you’re ready to roll.

Manual Mode

Hey, what about Manual Mode? Don’t worry – you can get there any time. Let’s say you’re into a User or Preset Bank, and have a particular Channel selected. The

channel’s corresponding LED is lit above its Floor Board Channel Select switch, 6 • 3 right? OK, step on this switch a second time and hold it for at least a second.

Boom! You'll find yourself transported directly to Manual Mode. To get back out of Manual Mode, use the Bank Up or Bank Down foot switches to go to a User Bank, and then you can do that “both switches at once” dance to get into the realm of the Preset Banks.

Editing and Saving Setups with the Floor Board

The basic story on editing setups is on Page 5•2 of this manual. With a Floor Board you’ll find that the display ( 22) will show an E (for “Edited”) whenever

you’ve edited a channel, as opposed to U (User) or P (Preset). It will display an S (Save) if you press the Save button on the Flextone in preparation for saving a channel. When you decide you want to save an edited channel, you can select any of the User Bank locations via the Floor Board as your destination. Here’s how:

1.EDIT A CHANNELS SETUP TO YOUR LIKING.

2.PRESS THE SAVE BUTTON ON THE FLEXTONE.

3.PICK THE USER BANK YOU WANT TO STORE THE SETUP IN WITH THE BANK UP AND BANK DOWN SWITCHES ON THE FLOOR BOARD.

4A. ON THE FLEXTONE, PICK THE CHANNEL MEMORY LOCATION (A, B, C, OR D) YOU WANT TO SAVE THE SETUP TO WITHIN THE SELECTED BANK, AND

5.PRESS THE SAVE BUTTON TO COMMIT THE SETUP TO THE FLEXTONES MEMORY. OR,

4B. SKIP 4A AND 5, AND JUST KICK YOUR CHOSEN FLOOR BOARD CHANNEL SELECT SWITCH TWICE TO SAVE THE SETUP INTO THAT CHANNEL.

Image 33
Contents Floor Board and FB4 Page Serial no Page Grand Tour Page Quick Start Guide MANUAL? I DON’T Need no Stinking ManualRegister and GET Great Free Stuff GET ON-LINE INTRODUCTION1 FLEXTONE! Meet the FlextoneTubetone Modeling AMP Models Front Panel Controls Grand TourChannel Select Switches A, B, C, D You use these Grand Tour Front Panel Controls Rear Panel USE the Right Cable Effects Send and Return HD folks, see . For allFlextone Flavors Which Amps are MODELED? Modeled AmpsModeled Amps Which Amps are MODELED? Modeled Amps Which Amps are MODELED? Modeled Amps Which Amps are MODELED? Flextone Signature Sounds Modeled Amps Flextone Signature Sounds Onboard Effects Flextone EffectsFlextone Effects Onboard Effects Flextone Effects Onboard Effects Combined Effects Delay/ChorusUsing the Manual Channel Features Using the Channel MemoriesCreating & Storing Sounds Edit Mode Preset Reset Button Page THAT’S Using Your Feet Using the Floor Board with the FlextoneGetting Connected Channel Select Mode TWO ModesBanks Manual Mode Editing and Saving Setups with the Floor BoardChannel Select Tap Tempo TunerWah Pedal Effect ON/OFF Mode Volume PedalDistortion Drive/BoostTrem/Chorus Delay Effect On/Off Settings Stored With Programmed ChannelsReverb Using the FB4 with the Flextone Flextone HD Inside Your HeadFront Panel Heat Sinks and Fans Fans and What Makes Them GOEffects Loop Series VS. Parallel Making Connections Using the Effects LoopSetting Effect Levels Direct OutputsDirect Output Level Take a Load OFF MONO/STEREO DetailFeeling UNBALANCED? Floor BOARD, More MEMORIES, & Midi Midi OUTMore Memory Midi Program Change & Flextone Channels Things to Remember with MidiMidi Continuous Control Midi Program Changes & Flextone Channels Visual Aid Cabinet HOOK-UPS Volume LevelsCarrying a Load Flextone HD Power OutputOPEN-BACK /CLOSED-BACK Emulation Cabinet ChoicesTypical 16 Ohm Wiring Setup Rewiring 16 OHM CabinetsHD Cabinet HOOK-UP Drawings 715 HD Cabinet HOOK-UP Drawings 717 HD Cabinet HOOK-UP Drawings 719 HD Cabinet HOOK-UP Drawings This page should be Left Blank do not Print this Text Appendix a AMP Models Appendix B Effect Parameters WHO’S RESPONSIBLE? Flextone Design TeamFlextone Manual was brought to you by Index Fans Flextone HD Manual Mode 23, 51, 52 Closed-back cabinet Tone emulation with HD This page should be Left Blank do not Print this Text