Line 6 Flextone Cab 212S user manual Rewiring 16 OHM Cabinets, Typical 16 Ohm Wiring Setup

Page 51

Flextone Manual Rev E; bookfile Page 51 Tuesday, September 8, 1998 10:31 AM

InsideYour Head: CABINET HOOK-UPS

hold down the Channel A button on the HD, and the emulator is switched off. Once you’ve turned it on, the emulator will stay on until you clear it with another power up while holding the button, so don’t forget to switch it off when you get back to the mondo stack stage setup again!

When you ﬁrst turn on the Flextone HD, it will ﬂash the Channel A or Channel B light brieﬂy to let you know which kind of cabinet it’s expecting to get plugged into: Channel A will ﬂash brieﬂy for closed-back, Channel B ﬂashes brieﬂy for open-back.

REWIRING 16 OHM CABINETS

If you’ve got a 4x12", 16 ohm cabinet that you’d like to use with the HD, you’ll ﬁnd that most setups will work better – giving you more volume – with a 4 ohm cabinet. You can convert your 16 ohm cabinet to 4 ohm by rewiring the speaker connections inside the cabinet. The two illustrations below show the signal ﬂow between the four speakers and the cabinet’s input jack in each setup. Line 6 doesn’t recommend that you do this yourself, unless you’re an experienced soldering iron jockey, but if you’ve got the know how – or you know someone who does – here’s a drawing you may need:

7•13

Typical 16 Ohm Wiring Setup

4 Ohm Wiring Setup

Image 51

Contents Floor Board and FB4 Page Serial no Page Grand Tour Page Quick Start Guide MANUAL? I DON’T Need no Stinking ManualRegister and GET Great Free Stuff GET ON-LINE INTRODUCTION1 FLEXTONE! Meet the FlextoneTubetone Modeling AMP Models Front Panel Controls Grand TourChannel Select Switches A, B, C, D You use these Grand Tour Front Panel Controls Rear Panel USE the Right Cable Effects Send and Return HD folks, see . For allFlextone Flavors Which Amps are MODELED? Modeled AmpsModeled Amps Which Amps are MODELED? Modeled Amps Which Amps are MODELED? Modeled Amps Which Amps are MODELED? Flextone Signature Sounds Modeled Amps Flextone Signature Sounds Onboard Effects Flextone EffectsFlextone Effects Onboard Effects Flextone Effects Onboard Effects Combined Effects Delay/ChorusUsing the Manual Channel Features Using the Channel MemoriesCreating & Storing Sounds Edit Mode Preset Reset Button Page THAT’S Using Your Feet Using the Floor Board with the FlextoneGetting Connected Channel Select Mode TWO ModesBanks Manual Mode Editing and Saving Setups with the Floor BoardChannel Select Tap Tempo TunerWah Pedal Effect ON/OFF Mode Volume PedalDistortion Drive/BoostTrem/Chorus Delay Effect On/Off Settings Stored With Programmed ChannelsReverb Using the FB4 with the Flextone Fans and What Makes Them GO Inside Your HeadFlextone HD Front Panel Heat Sinks and FansEffects Loop Series VS. Parallel Making Connections Using the Effects LoopSetting Effect Levels Direct OutputsDirect Output Level Take a Load OFF MONO/STEREO DetailFeeling UNBALANCED? Floor BOARD, More MEMORIES, & Midi Midi OUTMore Memory Midi Program Change & Flextone Channels Things to Remember with MidiMidi Continuous Control Midi Program Changes & Flextone Channels Visual Aid Cabinet HOOK-UPS Volume LevelsCarrying a Load Flextone HD Power OutputOPEN-BACK /CLOSED-BACK Emulation Cabinet ChoicesTypical 16 Ohm Wiring Setup Rewiring 16 OHM CabinetsHD Cabinet HOOK-UP Drawings 715 HD Cabinet HOOK-UP Drawings 717 HD Cabinet HOOK-UP Drawings 719 HD Cabinet HOOK-UP Drawings This page should be Left Blank do not Print this Text Appendix a AMP Models Appendix B Effect Parameters WHO’S RESPONSIBLE? Flextone Design TeamFlextone Manual was brought to you by Index Fans Flextone HD Manual Mode 23, 51, 52 Closed-back cabinet Tone emulation with HD This page should be Left Blank do not Print this Text