Pioneer CDJ-100S specifications Disc LOADING/UNLOADING, Display Window

BEFORE OPERATIONS: PANEL FACILITIES
Display Window
	6 A.CUE indicator
	Lights when the AUTO CUE function is used.
	7 Playback address display
	The elapsed playback time or remaining playback
	time of the track playing is roughly indicated with
	the full-scaled bar graph.
	Ö	When no disc is in the
1 TRACK number display	Ö	disc compartment	off
		When displaying elapsed
Displays the current number of the track playing.	Ö	playback time	lights up from the left side
2 CUE indicator		When displaying remaining
Flashes when it is possible to input cue point, and	Ö	playback time	turns off from the left side
lights steadily after the completion of input.		When remaining playback time is
3 Time display (REMAIN)		less than 30 seconds	blinks

The elapsed playback time of the track being played	8	WAH indicator
(when the REMAIN indicator is off) or the remaining		Lights or blinks when WAH function is active. ] P. 11
playback time of the track being played (when the	9	Pause indicator (*)
REMAIN indicator is on) is displayed in minutes (M)

and seconds (S), or frames (F). Blinks during pause mode.

4Playback tempo display

Tempo changes made with the TEMPO control knob are performed in 0.1% steps in the ±10% range. 0 to +10% in the +10% to –16% range is indicated in 0.1% steps and 0.2% steps from 0 to –16%.

5MT indicator

Lights when the MASTER TEMPO function is used.

0ZIP indicator

Lights or blinks when ZIP function is active. ] P. 11

-JET indicator

Lights or blinks when JET function is active. ] P. 11

=Play indicator (#)

Lights during playback.

DISC LOADING/UNLOADING

Label surface up

Insert straight

1. Set the rear-panel power switch to ON.

Do not force a disc into the unit when the power switch is set to OFF as this may damage the disc and the unit.

2.Insert a disc.

¦Hold the disc with label surface upwards, and in- sert into the front panel disc loading slot .

¦When playing an 8 cm (3-inch) disc, place the disc in a commercially available CD adapter before in- serting in the loading slot.

¦Only one disc can be loaded at a time. Never at- tempt to load more than one disc at the same time, or attempt to load a second disc when one disc has already been loaded.

¦When loading a disc, do not placing any twisting force on the disc, or try to force the disc into the slot. Also, do not attempt to interrupt or defeat the motion of the disc when the player begins to draw a disc into the slot or to eject a disc, since damage to the disc or player could occur.

3.Press the EJECT button to remove discs.

¦When the EJECT button is pressed, disc rotation stops and the disc is ejected from the loading slot.

¦If the disc fails to be ejected when the EJECT but- ton is pressed, the accessory forced eject pin can be inserted into the front-panel's forced eject hole to eject the disc. ] P. 4

CAUTION

Do not attempt to press a disc back into the slot when the EJECT indicator appears. Pressing a disc back into the slot while the EJECT indicator appears may cause the player to stop. In this case, press the EJECT button again and wait until the EJECT indicator goes out before reinserting the disc.

PRECAUTIONS ON PLAYING CD SINGLES (8 cm/3- inch Discs)

1When playing CD singles (8 cm/3-inch discs), al- ways use the adapter for 8 cm/3-inch discs. Be- fore loading the disc into the CD player, be sure to check that it is secured properly by the catches of the adapter. If discs have been inserted without the adapter by mistake, remove the disc immedi- ately by pressing the eject button. If the disc does

not come out with one press, press another time.

2Use 8 cm/3-inch disc adapters labeled with the 'mark (recommended standard product). Do not use adapters which cause the disc to idle, nor adapters which are bent or curved.

8

<DRB1232>

En